04: For the piping system, compute pressure at A, and mid pipe 2. If pipe (3) & pipe (4) havi equal discharge, and pipe (1) have the same properties of pipe (5). Neglect minor losses. (S F S) Pipe 1 Pipe 2 Pipe 3 Pipe 4 L (m) 300 460 245 30 D (cm) Q (//sec) 365 38 20 30 566 f PB (kPa) Pipe 1 0.027 500 Pipe 2 Pipe 3 B Pipe 4 Pipe 5

04: For the piping system, compute pressure at A, and mid pipe 2. If pipe (3) & pipe (4) havi equal discharge, and pipe (1) have the same properties of pipe (5). Neglect minor losses. (S F S) Pipe 1 Pipe 2 Pipe 3 Pipe 4 L (m) 300 460 245 30 D (cm) Q (//sec) 365 38 20 30 566 f PB (kPa) Pipe 1 0.027 500 Pipe 2 Pipe 3 B Pipe 4 Pipe 5

Name: 04: For the piping system, compute pressure at A, and mid pipe 2. If
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 04: For the piping system, compute pressure at A, and mid pipe 2. If pipe (3) & pipe (4) haviequal discharge, and pipe (1) have the same properties of pipe (5). Neglect minor losses. (SFS)Pipe 1L (m)Pipe 2460Pipe 3300Pipe 4365D (cm)Q (1/sec)24530302

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 400 gpm piping system is composed of the following pipes and fittings. Using the chart; Determine the Following: a. Equivalent length at suction in ft b. Equivalent length at discharge in ft c. Total friction loss in the installation, in ft. Suction side (4.5” Փ) Length of straight pipe 210 ft Long sweep elbow 5 pcs Standard Tee 2 pcs Globe valve 1 pc Checked valve 1 pc Gate valve (fully open) 1 pc Discharge side (4.0” Փ) Straight pipe 200 ft Standard elbow 4 pcs Standard Tee 3 pcs Gate valve (fully open) 1 pc
The ratio of entry diameter with exit diameter is 0.4 in a control volume of pipe segment. What is the corresponding ratio of entry to exit velocity? Recall Q1=Q2 and v1A1=v2A2 Correct answer has a margin of 0.1 from exact answer.
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.. A cylindrical tank 5 ft high has a constant diameter of 4 ft is full of water. The tank has a hole2. A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a holein its bo]om that measures 0.1ft^2. All losses are insignificant. How long will it take for the tankto empty? Note that you can NOT assume a staLc head and constant flow rate because thewater head in the tank decreases as the water flows out of the tank (A) 35 sec(B) 70 sec(C) 105 sec(D) 140 sec
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.1. A schedule-40 pipe necks down from 24 in at point A to 12 in at point B. 8 *3/sec of 60°Fwater flow from point A to point B. The pressure head at point A is 20 *. FricLon is insignificantover the distance between points A and B. What are the magnitude and direcLon of theresultant force on the water? (A) 2900 lbf; toward A(B) 3500 lbf; toward A(C) 2900 lbf; toward B(D) 3500 lbf; toward B
Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]
) where AP is the static The Hagen-Poiseuille equation for the laminar flow through a circular pipe is: AP pressure drop measured over some length of pipe, L. Use the Hagen-Poiseuille equation and the Darcy-Weisbach equation to derive an expression for the fanning friction factor, f, for laminar flow through a circular pipe where Re is the Reynolds number. Choose one answer from the list below: of= of O None of the above 32 Re 16 Re O f = 64 Re = o f = 32μLc 3 d² 8 Re O f = 16 Re
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?
oblems: 1. A horizontal pipe, 1 ft. in diameter, tapers gradually to 8 in. in diameter. If the flow is 500 cu ft. of water per minute, what is the difference between the pressures at the two sections? Ans. PA - PB = 443.63lb per sq ft 2. Water flows through a horizontal pipe at a velocity of 50 ft. per sec. Owing to the pipe gradually expanding to a larger size, the velocity decreases to 35 ft. per sec. What is the difference between the pressures at two points, one in each size of pipe? Ans. Pg - PA = 1,236. 75 lb per sq ft
QI/ A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e=0.026mm, v =1.13* 10“ m²/sec). Fig(1). 6m 23m Fig.(1) Nozzle
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2