1 The condenser can be part of which loop(s)? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 2 The evaporator can be part of which loop(s)? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 3 Which loop is eliminated in a direct expansion (DX) system? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 4 What are some benefits of using a "packaged" piece of cooling equipment rather than a "split" system?

1 The condenser can be part of which loop(s)? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 2 The evaporator can be part of which loop(s)? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 3 Which loop is eliminated in a direct expansion (DX) system? a- Airside loop b- Chilled-water loop c- Refrigeration loop d-Heat-rejection loop e-Controls loop 4 What are some benefits of using a "packaged" piece of cooling equipment rather than a "split" system?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 5RQ: The__________loop is used to distribute heated or cooled air to the building of a geothermal heat...

See similar textbooks

Similar questions

Questions: 1) The cooling tower is a part of: a. Air cooled refrigeration system. b. Water cooled refrigeration system- C. Low capacity refrigeration system. 2) The closed type cooling tower need pumping system less head than open type because: a. The water loop is short. b. The water loop is dosed. c. The loop is open. 3) The air wet bulb temperature effect on the perftormance of cooling tower in: a. Range b. Арproach. C. Both. 4) The centrifugal cooling tower is: a. Induced draft type. b. Blow through type. c. Draw through type.
Problem 3 For the system to the right, why would we want to heat the hot water heater using the HVAC system, rather than more traditional methods (such as burning natural gas)? Home inside nir temp: 20°C hot wnter henter - 10 liters imax temp: 50'C) Subrooler (autside air temmp: 32°C) R14a refrigerant PJ P2 sat. Hquid Qhot-water P2= OF 16 MPa T2=70°C P4-P2 Throttle (adinbatic) Compressor ladiabatic) Fan PS = P13 Pl=400 Pa at vapor air flow Tair =-10°C
1. A temperature drop in the coolant entering the primary loop can be dangerous because,(a) Reactivity can increase as a result.(b) Pressure in the primary loop will decrease and water can flash to steam.(c) All of the above.(d) None of the above
Space storage food requires system cooling capacity 10 ton refrigeration operates in the evaporator temperature -17.8 °C and temperature condenser 33.9 °C. Refrigerant used is R-717 and system operate on conditions saturated. Specify: a. COP = b. The flow rate of the refrigerant = kg/s. c. The rate of heat loss in condenser = kJ/s.
O a. None of these O b. Absolute pressures and heat capacity ratio O C. Absolute pressures and temperatures O d. Gauge pressures and temperatures In perfect gas law experiment, the pressure pump coupling is used to connect the vacuum vessel to the pump discharge connector. Select one: O a. False O b. True Which part in the mechanical heat pump is used to reduce the refrigerant pnessule? Select one:
Explain in detail the working of chilled water fan coil unit after it receive water from district cooling.
High- temperature source Generator Condenser 3+ Expansion valve Valve Pump Absorber Evaporator Refrigerated region Cooling water In the absorption refrigeration cycle, which of the follov the compressor in the vapor-compression cycle? componennts replace absorber, pump & generator condenser, expansion valve & evaporator generator, condenser & expansion valve condenser, generator & pump evaporator, absorber & pump expansion valve, evaporator & absorber Weak solution Strong solution
- Industrial Motor Controls, 12.a. What is the purpose of thermostat number 2, IN7, in the mixing vat machine?A. This thermostat is used to monitor the temperature of the incoming fluids.B. This thermostat is used to prevent an over-temperature condition in the event thermostat one sticks open.C. This thermostat is used to turn off the mixing motor after the mixture reaches temperature.D. This thermostat is used to shut off the heater when the chemical mix reaches setpoint.12.b. Why are motor current readings from a frequency inverter not exact readings of motor current?A. Because the output of a frequency inverter is not a sinewaveB. Because a frequency inverter adds a DC voltage level to the AC waveformC. Because a frequency inverter uses a lower voltage sinewaveD. Because the inverter pulses the motor with various sinewave frequencies
Draw the schematic and p-h diagram for the problem below: A two-stage cascade refrigeration system uses ammonia as refrigerant. The mass flow rate in the high-pressure loop is 0.10 kg/s. The condenser saturated temperature is 38 degree Celsius and the evaporator temperature is -40 degree Celsius. The cascade condenser is a direct contact type. Determine a.) the refrigerating effect in tons of refrigeration, b.) the power required, and c.) the COP.
Brief the Mechanical refrigeration system highlighting the working principle, process, componentsand P-h Chart.
(b) Bathroom sinks and some other fixtures include an overflow opening in the basin. This opening is located on the wall and near the top of the basin. The overflow opening serves two important functions: If the water tap is left on while the drain stopper is closed, the opening will channel water down into the drain opening rather than letting is spill out of the sink onto the floor. The overflow allows the sink to drain faster by introducing air into the system. A sink with a dimension given in Figure Q2(b), has water flows into it at a rate of 8 L/min. If the drain stopper is closed and water level in the sink remains constant, determine the average velocity of water flows through the 3.0 cm diameter overflow hole. Front 3 cm diameter overflow holes Q-8 L/min 15 3/4| 40 cm 15 cm Side (a) Figure Q2: (a) Picture of the sink; (b) Sink dimension (Ь)
without the presence of ____ there will be no cooling effect to the refrigeration system. it is the blood of the refrigeration system due to the effect of its evaporation process