1- Your customer (me, for example) requested a dice game machine that is described as: When a "start" button is pressed, then it does its functions given below: It accepts two 2-digit binary numbers. Each number can be one of 1, 2, or 3. The input of O will illuminate an error LED. If the total of these 2 numbers are 4, then it illuminates a winner LED. If the total of these 2 numbers are 6, then it illuminates an ultra-winner LED. Other total results will illuminate a loser LED. Please design and draw the logic circuit

1- Your customer (me, for example) requested a dice game machine that is described as: When a "start" button is pressed, then it does its functions given below: It accepts two 2-digit binary numbers. Each number can be one of 1, 2, or 3. The input of O will illuminate an error LED. If the total of these 2 numbers are 4, then it illuminates a winner LED. If the total of these 2 numbers are 6, then it illuminates an ultra-winner LED. Other total results will illuminate a loser LED. Please design and draw the logic circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A person is recording measurements from an analog data reader. During the first reading, he was not looking at the meter from a straight angle. He gets the reading of 72. At a second reading later he looks straight at the machine and gets the reading of 70. a) Which reading number is nearer to the actual value? What is the error type that happened in that reading? b) c) Suppose the data reader becomes faulty due to the extreme heat and gives a third measurement of 65. What type of error happened now? The data reader is working properly now, but there is a slight difference between two readings for the same measure. What type of error happened now and how can we d) minimize it?
Task 1: You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The arithmetic unit takes as inputs two 4-bit numbers (A and B) and one control input (M) add/subtract selector that selects the type of operation the unit will perform. When the input control is ‘0’, the input numbers are added. When it is set to ‘1’, the two input numbers are subtracted (A - B)
Question No.3: Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “5410” should display on 7-seg Display and when user press 2 leds should glow 5 times in a loop. If any other key is pressed no action should be taken
Question 8: Determine the decimal values of the following unsigned numbers: (a) (0111011110)2 (b) (1011100111)2 (c) (3751)8 (d) (A25F)16 (e) (FOF0)16
Note: Attempt all questions. Any proof of cheating may lead to cacelation of paper. Q.1 Draw the and-or logic circuit using the input (A, B, C) and output (X) waveforms in Figure 01. Inputs B Output X FIGURE 01
A system uses two-dimensional parity. Find the parity unit for the following three data units: 00110 11001 00001. Assume even parity. (write down the sequence of 0's and 1's without any blank space). hints: answer is 6 bit
Convert the number 1100000 from binary to decimal, show your work. Answer:
Convert the following hexadecimal numbers to the decimal number system. please show all steps a. C b. 41 c. 9E d. 138 e. 12A
a. (697)10 into Octal and Hexa decimal b. (2D9)16 into Decimal and Octal
I want to solve this question using digital logic material
Program The first number 98H is placed in the memory location 2501 H. The second number 87H is placed in the memory location 2502H. The result is stored in the memory location 2503 H.
The observation of a certain measurement is described by the following figure. 'True' value A Which of the following statement is correct ? O a. low accuracy and high precision O b. low accuracy and low precision Oc high accuracy and low precision O d. high accuracy and high precision