I need answer within 20 minutes please please with my best wishes CI Answer of the following:1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than theoil (SAE 20) at the same temperature. (True or False)2. For a slow speed-highly loaded bearing, used oils of high viscosity; while for high-speedbearings, uscd oils of low viscosity. (True or False)3. An increase in radial clearance increases the load capacity bearing capacity of the bearing.(True or False)

To decrease the friction losses in the bearing oil is used .varios types of the oils are used for…

1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than the oil (SAE 20) at the same temperature. (True or False) 2. For a slow specd-highly loaded bearing, used oils of high viscosity; while for high-speed bearings, uscd oils of low viscosity. (True or False) 3. An increase in radial clearance increases the load capacity bearing capacity of the bearing. (True or False)

1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than the oil (SAE 20) at the same temperature. (True or False) 2. For a slow specd-highly loaded bearing, used oils of high viscosity; while for high-speed bearings, uscd oils of low viscosity. (True or False) 3. An increase in radial clearance increases the load capacity bearing capacity of the bearing. (True or False)

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter8: Preventive Maintenance And Basic Services

Section: Chapter Questions

Problem 20RQ: True or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight...

See similar textbooks

Similar questions

State four (4) behavioral characteristics of black oils if pressure of reservoir is above the bubble point pressure (pres > Po).
The rate of change of viscosity with temperature is known as viscosity index and high viscosity index means oil will remain the same over a wide range of temperatures, Select one: True False
Describe the operation of different types of lubrication methods used in a petrol engine (80 - 100 Words) a. Boundary lubrication b. Hydrodynamic lubrication c. Force Feed lubrication d. Mist Feed (Boundary) Į A▾ B I W LEM III
True or False? An oil with the classification of 5W-30 has the viscosity of both a 5- and 30-weight oil. The 5W means the oil has a viscosity of 5 when warm and a 30 rating when it is cold.
b) A gasoline engine is specified to be 4-stroke and four-cylinder. It has a bore of 80 mm and a stroke of 100 mm. On test it develops a torque of 75 N.m when running at 3000 rpm. If the clearance volume in each cylinder is 60 cm², the relative efficiency is 0.5 and the calorific value of the fuel is 42 MJ/kg; determine the brake thermal efficiency. Root wicl
33) A multiple disc clutch, steel on bronze, is to transmit 7 kW at 1000 rpm. The inner radius of thecontact is 50 mm and outer radius of the contact is 75 mm. The clutch operates in oil with an expected coefficient of "0.1". The average allowable pressure is 0.35 N/mm2. Determine the total number of steel and bronze discs.
Which of these provides stringent classifications formulated for engine oils used in European vehicles? Select one: a. SAE b. API c. ILSAC d. ACEA
what is the bearing similarity number for the ideal inner radius/outer radius ratio in a hydrostatic axial sliding bed with the oil pocket in the middle? A.0.35 B.2.35 C.0.5 D.1.35 E.0.25
Which of the statement correct? fluid dynamics and statics examine fluid separately The effect of application of force in fluids is instantaneous Hydrodynamics is part of fluid statics
Fluid machineries question Complete solution pls and correct units.
20q Full film lubricating is a type of lubrication in which the coefficient of friction is low. Select one: True False
46 lll l G O 4 o A:E0 1 aj3vkuusfe 8:45 195% . tutorial-1.pdf Example: Single cylinder, four stroke petrol engine has a bore of 0.07 m and diameter of 0.1 m. The engine is delivering a torque of 35 N.m. Calculate the brake mean effective pressure. ahmed majhool 14 مشارك آخر غزوان احمد عمار حسن ...