1. In the bulk deformation process, there is a change in the thickness of the wokpiece. Thus, the ratio of the surface area to the volume is... B. very high. c. small. a. equal. 2. In the metal forming process, if the temperature increases, the metal working becomes easier due to reducing in a. n and K. 3. The true tensile strain can be calculated from the following relation.. a. e =In (1+e). b. melting temperature. C. hardness ..... b. e =In). C.e = In

1. In the bulk deformation process, there is a change in the thickness of the wokpiece. Thus, the ratio of the surface area to the volume is... B. very high. c. small. a. equal. 2. In the metal forming process, if the temperature increases, the metal working becomes easier due to reducing in a. n and K. 3. The true tensile strain can be calculated from the following relation.. a. e =In (1+e). b. melting temperature. C. hardness ..... b. e =In). C.e = In

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a steel sample under tensile testing, if the first principal strain was equal to 0.005 and all other principal strain components are zero. If steel has a Lame's constant of 100 MPa and Shear Modulus of 10 MPa. If we plotted the stress-strain curve of this test. What is the area under this curve? Select one: O a. 1500 MPa O b. 1500 kPa 3. O C. 1500 Joule/m O d. 1500 Joule/m O e. NONE
a . Sketch stress strain curve if the result shown in table represent the force and extension happened in steel, and show Mechanical properties that we get from tensile test on curve? (10p)Note : Lo=80 mm , Do=10 mm , use excel to plot the curve ExtensionLoad(mm) (N)0 0.900.83 4694.341.67 4831.412.50 4781.083.33 4918.834.17 4926.585.00 5257.075.83 5437.016.66 5575.888.33 5775.189.16 5847.5210.83 5965.4111.67 6010.5312.50 6042.5713.33 6072.2614.16 6092.9315.00 6113.2416.67 6140.3617.50 6146.3718.33 6148.1419.16 6149.1725.00 5940.2125.83 5675.3326.67 4725.52b. What is meant by modulus of rigidity? if it increases what does happen to material? (2p)
1) For a certain metal, the strength coefficient= 700 MPa. A tensile specimen of the metal with gage length = 150 mm is stretched to a length = 207 mm. a) Determine the value of the strain-hardening exponent for the metal that will cause the average flow stress to be 3/4 of the final flow stress after deformation. b) Determine the flow stress at the new length and the average flow stress that the metal has been subjected to during the deformation.
Forming is a material shaping process-using application of force. Select one: .True .False
The laboratory mechanism used to test the fatigue life of materials is Select one a. A rotating shaft with an applied torsion load b. NONE c. A rotating shaft with an applied axial load d. A rotating shaft with an applied bending load e. A rotating shaft with an applied combined load
Pleas very fast A square cross-section v-notched specimen of height 75 mm has each side of 13 mm has been selected to perform Charpy impact test. A v-notch of thickness 1.97 mm is made at the middle of the specimen length. Determine the cross-sectional area at notch. Cross-sectional area at notch (in mm2)
Given the following stress-strain graph:a. is the modulus of elasticity of "A-514" greater, less or equal to the one of "A-572"?b. from the previous question, make an estimatio for both of them, check that the graphic comes in %c. If we were to test these materials in a universal tension equipment, which one would withstand more load?d. If we were to test these materials in a universal tension machine, which one would elongate the most before fracturing? would elongate the most before fracturing? e. Of the 6 materials shown, do any behave as brittle materials? f.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa 2. Using MOHR CIRCLE, what is the resulting "HORIZONTAL" SHEARING STRESS at the given angle plane point? a. 44.03 MPa b. 64.32 MPa c. 185.68 MPa d. 75.00 MPa 3. Using MOHR CIRCLE, what is the resulting "VERTICAL" NORMAL STRESS at the given angle plane point? a. 44.03 MPa b. 75.00 MPa c. 64.32 MPa d. 185.68 MPa
Q.3. A cylindrical specimen of cold-worked Brass has a tensile strength of 500 MPa. If the specimen remained cylindrical during deformation and its original radius was 10.6 mm, determine its radius after deformation. The dependence of tensile strength on percent cold work is shown in the following Figure. 140 900 1040 Steel 120 800 700 100 600 Brass -80 500 -60 400 Copper 300 -40 200 10 20 30 40 50 60 70 Percent cold work Tensile strength (MPa)
Choose the correct answer Stress divided by Rate of strain is: d. Velocity a. Surface tension f. Kinematic viscosity b. Density e. Dynamic Viscosity c. Unit less
As Fast As you can Please mak sure the answer is correct 100% Please match the following to the appropriate areas or sublocations illustrated on the steel stress-strain curve shown below: (ultimate tensile stress- yield stress - repture stress) (4) The maximum stress point on the stress strain curve. (2) The point where the proportional limit ends and the moment the elastic limit of the specimen is reached, the specimen will return to its original state after the loading is removed. Typically occurs before the steel specimen starts to plastically yield. (5) The point at which the steel specimens has underwent necking and breaks. This typically occurs after the maximum stress is reached during the experiment.
Match the items in columns I and II. Column-I Column-II 1. Fluidity P. Charpy Q. Knoop 2. Microhardness R. Spiral test S. Cupping test 3. Formability 4. Toughness 5. Permeability (a) P-4, Q-5, R-3, S-2 (b) P-3, Q-5, R-1, S-4 (c) P-2, Q-4, R-3, S-5 (d) P-4, Q-2, R-1, S-3