Please do hand calculation only for Ix 1. Please plot the I-V curve (Ix-Vx) of a diode shown in Fig.1 by LTspice DC sweepanalysis. With exponential model and Is=1*10-16A, please fill the Table. I below.[Hint: use exponential model in tutorial P.20 and Is in the command representssaturation current.]type of sweep Linearstart value = 0.6stop value = 0.8increment = 0.1m1xIx when Vx = 0.6VIx when Vx = 0.8VVxFig. 1☑D₁Table. IHand CalculationLTspice Simulation

Answered: 1. Please plot the I-V curve (Ix-Vx) of…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
How is a solid-state diode tested? Explain.
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
As shown is a positive parallel clipper circuit which has an input voltage of E=t5V. The negative output voltage is to be -4.5V when lo is 5mA. Assume ideal diode model approximation. Determine the value of R1 in ohms. Note: Write only the numeric value of the answer, round to 4 decimal places. No need to include the unit. R, +E ww Output Input D, -E -(E-1,R,)
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
Determine the maximum value of Vi that will maintain the Zener diode in the on' state given Vz=13V, Izw=63MA, R=3150, RL=1.2ka. Vz Lütfen birini seçin: a.21.9V b.94.2V c.36.3V d.56.1V e.86.4V
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
4. Assume the Blue LED has a forward turn on voltage of 4 V and exhibits ideal diode behavior. For the circuit below, sketch the voltage across the diode and the voltage across the resistor (versus time) for the following Vin values. On your waveforms, indicate the time periods when the LED is on. a. Vin= 3 sin(2π *60t) V b. Vin = 5 sin(2π *60t) V Blue LED # Vin 1k R2
3) Demonstrate clipping of negative waves with an inverted diode in the output. A circuit which removes the peak of a waveform is known as a clipper. Show a negative clipper. Produce a schematic diagram with LTspice schematic capture program. During the positive half cycle of the 5 V peak input, the diode is reversed biased. The diode does not conduct. It is as if the diode were not there. Show the positive half cycle is unchanged at the output V(2). Show the output positive peaks overlays the input sinewave V(1). Use in the LTSPICE display module, the command "plot v(1)+1)" accomplishes this. Voltage values: Resistor valuse: 1 ΚΩ DC offset: 0 V Amplitude: 5 V Freq: 1 KHz

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS