1. Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, 5 90MPA, Ta s 65MPA_ and the angle of rotation of the free end limited to 11°. Use GS = 84 GPa and Ga = 27 GPa 75 mm (30 pts) Aluminum Steel Bf 50 mm 1.5 m
Q: A single acting reciprocating pump has a bore of 15 cm an a stroke of 30 cm. The suction pipe has a ...
A: Given that, Bore of pump, db=15 cm,Stoke of pump, L=30 cm,Diameter of suction pipe, ds=10 cm,Speed o...
Q: the number of links that can rotate fully
A: Given: Four bar mechanism is made up of links of :length; p=200mm q=300 mm ...
Q: n a steam turbine system, what does a negative delta mH mean? Describe what happens to the fluid's e...
A: Turbine work is beneficial since it is carried out by fluid. Compressors, pumps, and fans are dev...
Q: If a rectangular duct system (12 inch × 26 inch) has an average velocity of 700 fpm, what is the air...
A:
Q: 3. Find the reactions at the supports A and B for the beam given below. The length of the beam is 12...
A:
Q: 20. Determine the Miller indices for the plane A shown in the following unit cell: +y +x (423) d. (3...
A:
Q: Relative velocity of link 1 with respect to link 2 is 20 m/s. link 2 rotates at constant speed 140rp...
A: Given:Relative velocity of link 1 with respect to link 2, v=20 m/sSpeed of link 2, N=140 rpm
Q: Write down the parameters considered in determining the basic dimensions of the friction clutch
A: Basic clutch design issues are presented, including friction elements during engagement, friction ma...
Q: A water strikes to a vane with stationary velocity 25 m/s as shown in the Figure 3. It is given the ...
A:
Q: A tube with 45 meters long, and a diameter of 1.8 meters and 2.3 meters, inlet and outlet respective...
A: Given Data: Length of the tube, L=45 m Inlet diameter, d1=1.8 m Outlet diameter, d2=2.3 m
Q: Select all forces that will NOT have an effect (moment) at point O. Assume each space is a 1x1 unit ...
A:
Q: A stepped shaft, as shown in Figure 4.35, has dimensions of D = 2 in, d = 1 in., and r = 0.1 in. It ...
A:
Q: A storage tank contains oil with specific gravity of 0.88 and depth of 20 m. What is the pressure at...
A: Given:Specific gravity of oil, S=0.88Depth of tank, h=20 m
Q: Superheated steam at 7.585 MPa (1100 psia) and 616.3 K (650 F) enters the high-pressure turbine of a...
A: At state 1 : Saturated water and P1=7kPa h1=163.3655 kJ/kg v1=.0010075 m3/kg Wp1=h2-h1=v1∆P h2-163.3...
Q: Energy Flux Malaysia has just launched a new type of house refrigerator system using R-134a as a wor...
A:
Q: e. Determine the maximum allowable value of P
A: Determine the maximum allowable value of p
Q: 100 R, Po1 =200 psia, an :11
A: As a piece of a task on microjet motor plan and production, this paper depicts exhaustively every on...
Q: 6. A card is drawn from a pack of 52 cards. The card is drawn at random. What is the probability tha...
A: Probability=required /total In a pack of card no.of spade=13 no.of jack=13 Probability ( neither spa...
Q: The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading ...
A:
Q: 1. A) Draw the mean effective pressure vs specific fuel consumption at constant speed and constant t...
A: Mean effective pressure The mean powerful tension (MEP) is an amount connecting with the activity o...
Q: Two designs for a beam are to be considered. Determine which one will support a moment of M= 150 kN....
A: Given: Bending Moment, M=150 kN-m M=150×106 N-mm
Q: One kg of steam with a quality of 20 percent is heated at a constant pressure of 800 kPa until the t...
A:
Q: A person is pushing on a uniform block of wood as shown in the figure and parameter table. The block...
A: Given: mass of the wood=140Kg coefficient of static friction of wood(μw)=0.25 so the weight of the w...
Q: A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with ...
A: Given data as per question dimensions of steel plate = 2.5 x 1.5 x 0.08 m weight of steel plate= ...
Q: For the following situations of steady flow, calculate the Reynold's Number and determine whether fl...
A:
Q: A thermal power plant of 800 MW capacity burns 50 T of coal/MW/day. Assume complete combustion of ca...
A: A burning response happens when a substance responds rapidly with oxygen (O2). For instance, in the ...
Q: A large spool of rope rolls on the ground With thế end the rope lying on the top edge of the spool. ...
A: The centre of mass of a mass distribution in space is the one place in space where the weighted ...
Q: 3. Determine the vertical and horizontal components of the reactions at pins B and C.
A: Drawing the reaction at A and D as shown below,
Q: Find the magnitude and direction of the resultant force for the system of forces shown in the figure...
A: Please check the correct answer in step 3.
Q: 2. Determine the individual moment about point A of each of the three individual forces acting on th...
A:
Q: 40 kN E 2 m B F 3 m 50
A: to find reaction component at B and C
Q: An automobile carburettor having its flost chamber vented to the atmosphere is tested. at sea level ...
A: (a) The venturi/throat pressure with air cleaner is 0.815 bar. (b) Air-fuel ratio with air cleaner i...
Q: Three forces act on the ring. If the resultant force FR has a magnitude and direction as shown, dete...
A:
Q: A prismatic bar with a length L = 1 m andcross-sectional area A = 1200mm2 is supported atthe ends. T...
A: If the temperature of the body is lowered or raised its dimension will increase or decrease correspo...
Q: 43. A two-stream annular fuel rod includes inner and outer cladding. Use the fol- lowing data and de...
A:
Q: What are the advantages and disadvantages of using robots in manufacturing? What will happen if robo...
A: Robots in Manufacturing : Now days, robots are widely used in manufacturing for automation purpose. ...
Q: A high-strength steel band saw, 21 mm wide, runs over pulleys 1200 mm in diameter. What minimum thic...
A: GivenW=21mmd=1200mmσ=280 MPaE=230GPa
Q: Steam flows isentropically through a nozzle from 1500 kPa, 300oC to 950 kPa. For 454 g/s of steam, d...
A: Given data as per question Initial pressure =1500 kpa Initial temperature = 300oC Final pressure =95...
Q: Determine the force in each member of the loaded truss. The forces are positive if in tension, negat...
A:
Q: A rectangular steel block is 4 inches long in the x-direction, 6 inches long in the y-direction, and...
A:
Q: 1. The weights of the various components of the truck are shown. Replace this system of forces by an...
A: Given question belongs to the subject Engineering Mechanics and can be solved suing the concept of e...
Q: Give the unit vector in spherical coordinates that extends from M(5,1,2) to N(2,4,5).
A:
Q: 12 bales of cotton, each weighing 486 lb, were held for conditioning in a humid warehouse kept at a ...
A:
Q: me a torque T4 of 7500 Nm acting on Ink 4. quired value of F, is. N. t friction, gravity and inerti ...
A:
Q: 2. Draw the complete shearing force and bending moment diagrams. 10 K 10 K 3 ft 8 ft 3 ft
A:
Q: The cross-sectional area of the bar is 5 cm2. L. Aluminum Steel Duminum 80 kN 20 kN 30 kN 70 kN B. 3...
A:
Q: 24. The rigid pipe BC shown is supported by a pin at C and an A- 36 guy wire AB (E = 200 GPa). The w...
A:
Q: The number of degree of freedom
A: Given: Links=32 Joints=41 where joints are simple revolute type. Find Degree of freedom of a planar ...
Q: 1, contractior 1. Consider a low speed subronic wind tunnel with a area ratio for the no2zle. If the...
A:
Q: (Problem 2) Alcohol (specific gravity = 0.80) is flowing through a horizontal pipe which is 10 inche...
A: Find the diameter of smaller section
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 2 images
- 2. The diameters of the solid shafts are: AB is 0.6 in, A B D BC is 0.75 in. and CD is 0.9 in. The applied torques are: TĄ = 400 in lb, Tg = 1200 in Ib, Tc = 500 in İb. Determine the maximum shear stress in each of the three shafts. TA TB Ans: TmaxAB = 9431 psi, TmarBC = 9658 psi, TmaxCD = 9082 psi Te Fixed to wallThe Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.2. The composite shaft of total length 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm diameter steel bar. The composite subjected to the total torque of 565 Nm. (GBr = 39 GPa and Gst = 77 GPa) 1.8 m -Brass jacket 30 mm Steel core 5 mm Figure composite shaft Determii e the following: a. Maxin um shearing stress in the brass. b. Maxin um shearing stress in the steel. c. Angle f twist of end Brelative to end A. זו
- Member ABCD is a hollow circular steel shaft with a 4 inch outer diameter and a 3 inch inner diameter. It is rigidly attached to the wall at A. Externaly applied torques are TB of 1338 lb-ft, Tc of 1117 lb-ft, and TD of 884 lb-ft. Firstly obtain the internal torque generated, then calculate and input the maximum shear stress in section BC of the shaft: (f v max) = ___________ lb/in.2. Pay attention to unit conversion and calculate your answer to 1 decimal place.Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, Ta s 65MPA_ and the angle of rotation of the free end limited to 11°. Use Gs = 84 GPa and Ga = 27 GPa 75 mm T 2T Aluminum Steel Bf 50 mm 2 m 1.5 mA solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
- Q-3 A 25-mm-diameter solid round bar has a groove 2.5-mm deep with a 2.5-mm radius machined into it. The bar is made of AISI 1050 CD steel and is subjected to a purely reversing torque of 250 N-m. For the S-N curve of this material, let f= 0.9.A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is ___KN-m 3.82 2.64 0.48 1.18 5.03Let's consider a solid circular shaft subjected to the torque loads as shown Determine the minimum required diameter "D" if the shaft is made of a material having a yielding shear stress Ty = 100 MPa, for a factor of safety FS = 2. The polar moment of inertia of a solid circular cross-section is given by Jr.R¹/2. 300 mm B 600 mm 100 N.m 500 N.m 600 mm 400 N.m
- If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twistA alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060 lb-ft, Tc= 860 lb-ft, and Tp = 280 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in %D Section 6.6. (b) If the allowable shear stress in the shaft is 5800 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp (3) В C D Answer: (a) T1 = Ib-ft T2 = Ib-ft T3 = Ib-ft (b) d = in.