Outcomes: After completing this lab, you should be able to:Verify NAND and NOR gates as universal logic gate.Troubleshoot basic gate IC's.Warning:1. Do all wiring or any change in wiring with power OFF, unless otherwise specified in the procedure.Make sure you are using the correct supply voltage as specified.2.3. Never reverse the polarity of the power supply to prevent damage to the IC. Refer to the IC's pinconfiguration or data sheet.Introduction:TTL IC gates will be used in this activity; an input left floating (disconnected) in TTL IC's isusually taken as a 1. A legitimate 1 input/output can range from 2.0V to 5V(input); 2.4V to5V(output), and a legitimate 0 input/output can range from OV to 0.8 V(input); OV to 0.4 V(output).NAND and NOR are universal gates because any Boolean expression can be realized bythese gates.Pin configuration of IC 7402VecEquipments:Digital Trainer KitSolid-core wireDigital IC: 7400, 7402.12A OLaboratory Activity 4UNIVERSAL GATESIC 740010510Procedures:1. Verify the function of a single NOR and NAND gate and develop the truth table.INPUTA0011Table 3.1 Truth Table of NOR and NAND Functions2. Make the connections of each circuit diagram and derive it's the truth table. Describe thefunction.B0101PIN Configuration of IC 7400VCC7GndFig 3.1 NOR and NAND GatesWHI27092OUTPUTOUTPUT(for NOR gate) (for NAND gate)YYGNDIC 7402Fig 3.2 NAND and NOR Does Other Logic FunctionsWHI27092

Input Output (For NOR gate) Output (For NAND gate) A B Y Y 0 0 0 1 0…

1. Verify the function of a single NOR and NAND gate and develop the truth table. OUTPUT (for NAND gate) Y A O во- 6 A 0 0 1 1 Table 3.1 Truth Table of NOR and NAND Functions. 2. Make the connections of each circuit diagram and derive it's the truth table. Describe the function. IC 7400 INPUT 10 B 0 1 0 1 OUTPUT (for NOR gate) Y - 270 Ω A BO IC 7402 Fig 3.2 NAND and NOR Does Other Logic Functions 10 27092

1. Verify the function of a single NOR and NAND gate and develop the truth table. OUTPUT (for NAND gate) Y A O во- 6 A 0 0 1 1 Table 3.1 Truth Table of NOR and NAND Functions. 2. Make the connections of each circuit diagram and derive it's the truth table. Describe the function. IC 7400 INPUT 10 B 0 1 0 1 OUTPUT (for NOR gate) Y - 270 Ω A BO IC 7402 Fig 3.2 NAND and NOR Does Other Logic Functions 10 27092

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Is there a standard measure for the amount of work a surge suppressor can do before it stops protecting a circuit from an electrical surge?
IV. PROCEDURES: For the AND gate look on the data sheets, connect the circuit on Breadboard and test the gate. Using logic switches SW1 and SW2, apply the logic levels 0 and 1 to gate inputs Create a truth table and record the results Also simulate the given gate using the Circuit Wizard simulation software Obtain the corresponding circuit diagram using the simulation software of the Boolean expression F((A,B,C)= АВ* AC * ВС From the obtain circuit diagram develop the corresponding truth table From the figure below obtain the equivalent Boolean expression and develop its corresponding truth Table АП сПо- Boolean Expression: Z= (AB)(CD)
Part2: Layout of basic logic gates (Layout) In this part you will design the layout the basic logic gates listed below. For each gate you have to: 1- Build the layout of the gate and show a snapshot of your work. 2- Show that your design is working by testing input combinations Required Gates: 1- 3-input NOR gate 2- 2-input NAND gate
Q3 /A)- Design an electronic circuit to drive Four (4) LEDs by using 741 Op-Amp. The internal resistance of each LED is 70 ?. The 741 Op-Amp can carry out maximum output current 20 mA, and requires minimum voltage of 5 V. After completing your design explain why used this kind of connection in your design ( you can use Ohm’s Law in yours explanation
The power absorbed by a 5k resistor in the circuit is 3.6 mW. Find voltage ?and current in the resistor I R- 5k2
What gate is shown below in the chart? Include the gate name, symbol and the equation.
Problem: In order to get my old car running again, the mechanic must adjust the car's timing. Normally, the spark plugs are replaced first. They will need to be adjusted to the correct gap width. My mechanic does this appropriately about 88% of the time. She must then adjust the timing belt to the manufacturer's specification, which she does about 97% of the time. Using the Technique for Human Error Rate Prediction (THERP) model and completing the event-tree diagram below, answer the following two questions. 1 What would the probability be of her getting my car running again if the two tasks are not interdependent (i.e., parallel)? Pr(success) = Pr(failure) = - Assuming these two tasks are interdependent (i.e., serial), what is the mechanic's probability of success (and failure)? Pr(success) = Pr(failure) =
Help Please You want to design a synchronous counter sequential logic circuit. Counting from 9 to 0and will not count the number 8. Design the sequential circuit using JK Flip-Flop. Explain each step. Desired actionshow that you have done
Task 5: Logic circuits with multiple outputs Find the Boolean expression of the outputs of the following circuit, D = E = Draw the circuit on EWB and simulate it to fill-in its truth table shown below (use logic converter please). Note: You need to use the logic converter two times, once for the output D, and another time for the second output E.
Design a password protected door lock system using logic gate. The system must have a mechanism to enter any numeric passwords. The system also should have a display which will show either the entered password is correct or not (using 7segment led display). If the user enter a wrong password he/she will be able to re-enter the password by pressing a specific button of the keypad. For a right password entry the door will be open. please explain how the every gate was function to make this system succeed.
Task: DL34. In digital electronics, a NAND gate (NOT-AND) is a logic gate which produces an output which is false only if all its inputs are true; thus, its output is complement to that of an AND gate. A LOW (0) output results only if all the inputs to the gate are HIGH (1); if any input is LOw (0), a HIGH (1) output results. A NAND gate is made using transistors and junction diodes. Minimum number of NAND gates required to implement the following binary equation (A'+B') (C+D)?
What are the lines should be connected to the OR gate (Assume output line are D0, D1....Dx)