1. When the plastic bushing shown to the right is inserted into a cylindrical enclosure, the insertion tools exert the forces shown in the figure to the right. The diameter of the bushing (cylinder) is 60 mm. Each of the forces is parallel to one of the coordinate axes. Find the resultant force and the resultant moment at point C. Ř=-2lî - 29j–16k N %3D Ans.: M =-0.87î +0.63ĵ+0.39k N - m C

1. When the plastic bushing shown to the right is inserted into a cylindrical enclosure, the insertion tools exert the forces shown in the figure to the right. The diameter of the bushing (cylinder) is 60 mm. Each of the forces is parallel to one of the coordinate axes. Find the resultant force and the resultant moment at point C. Ř=-2lî - 29j–16k N %3D Ans.: M =-0.87î +0.63ĵ+0.39k N - m C

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
Answer for the 1st part of the problem. magnitude of force A = 74 N direction of force A = 25o north of west second force = P direction of force P = α south of west arrow_forward The resultant of two forces is horizontal , it means that the y component of resultant = 0 Ry = ASin(25o) - PSin(α) 0 = (74×0.42) - PSin(α) PSin(α) = 31.08 NFor, the smallest force P , the value of Sinα must be maximum which is 1 when the value of αis 90 degree Thus, P×Sin(90o) = 31.08 N P = 31.08 N The magnitude of smallest force P = 31.08 N the direction of force P = 90 degree south of west = along - y axis= arrow pointing vertically downw
FY Find the two components of the force (200 N) if a= 60 degrees, as :shown in the figure below F= 200 N α= 60 FX (FX= 100 N) AND (FY= 73.2N) O (FX= 173.2 N) AND (FY= 100N) O (FX= 100 N) AND (FY= 173.2N) O
Find the values of P and F so that the four forces shown in the figure will produce an upward resultant of 300lbs acting 4ft from the left end of the bar?
1. Find the Forces A and acting on the Skg uniform rod as shown. Consider the welght of the rod. 70N 0.8 m 50N 1.3 m 5m 2 Find the torque produced by each force (R and strom the figure shown. R=30 N hinge 2 m 4 m S-30 N 12 m
The pipe is pulled by three cables as shown on the figure below. All three cables are subjected to known forces. Another cable is planned to be added on the system. This additional cable is designed to pull the pipe along the positive y-axis. The proposed cable, Fy is twice as much as the only force which tends to pull the pipe below the x-axis. (Fa= 7.5kN; Fb= 1.25kN; Fc=5kN) Find the summation of forces in x axis and y axis.
2000Lbs 30° 60° y A' \ B The bar OA is fully constrained at O and attached to the cable AB. The bar length is 20', and it forms a 30° angle with the z-axis and its projection on the x– y plane forms a 60° angle with the x-axis. The point B is prescribed by the coordinates (8',16',0). If the force in the cable is 2000Lbs, what is the moment of this force about O? What is the moment of the 2000Lbs force about the axis OÁ.
The width of the AB planar cover in Figure 2 is 10 m. The cover is sunken. It is articulated at point B. At point A, the wall is smooth. Find the resultant force and find the action centers of the forces Fx and Fy. γsu = 9.79 KN / m3 su= water duvar=wall kapak=cover dimension of AB = 10 units
Given the image below, if Tcg = 52.1N, what is the moment of tension in the cord cg about the x axis?
w1 Problem 4 From the figure, wi =15KN/m, w2=12kN/m, F1 =7kN 1. Find the resultant of the forces 2. Find the location of the resultant from point B. to 7m 4m 2m
The weight of the linkage AB =BC= 20KG .Find the force acts on bar BC -875 mm- B 400 625 mm 30 60 F = 800 N
SOLVE STEP BY STEP IN DIGITAL FORMAT The forces F1 and F2 in the figure are parallel to the x-axis, while the force F3 is perpendicular to the line AC, all of them applied to the triangular plate AEC shown. Given those conditions, replace that three-force system by an equivalent system at point E (Point E is considered the origin). |F3|=400 lb 10 in |F2=300 lb $300 B 15 in AY D E ans **** 15 in 5 in FR Mo |F₁|=250 lb = = -3701+240 [lb] 5150k[lb-in]