10 kip/ft 50 kip · ft A 5 ft 5 ft The simply-supported beam above is subjected to a uniformly distributed load and couple moment, as shown. The beam is supported by a pin at A and roller at B. Which of the following best describes the shape of the shear diagram between poim A and the midspan of the beam? a) zero b) constant c) linear d) parabolic e) cubic

10 kip/ft 50 kip · ft A 5 ft 5 ft The simply-supported beam above is subjected to a uniformly distributed load and couple moment, as shown. The beam is supported by a pin at A and roller at B. Which of the following best describes the shape of the shear diagram between poim A and the midspan of the beam? a) zero b) constant c) linear d) parabolic e) cubic

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The simply supported beam consists of a W21x44 structural steel wide-flange shape [E = 29,000 ksi; I= 843 in."1. Assume that the support at D can provide resistance either up or down. Fora loading of w= 7.2 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB= 10 ft, LBc = 5 ft, LCD =5 ft, LDE=5 ft. B LAB LBC LCD LDE Answers: (a) VA = in. (b) vc = in.
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“). Assume that the support at D can provide resistance either up or down. For a loading of w = 7.2 kips/ft, determine: (a) the beam deflection va at point A. (b) the beam deflection vc at point C. Assume LaB = 12 ft, LpBC = 6 ft, LcD = 6 ft, LDE = 6 ft. B D E LẠB LBC LcD LDE Answers: (a) VA = in. (b) vc = in.
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.*). Assume that the support at D can provide resistance either up or down. For a loading of w = 4.5 kips/ft, determine: (a) the beam deflection vg at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, LBC = 9 ft, LCD= 9 ft, LDE = 6 ft. B D E LAB LBC LcD LDE Answers: (a) VA = in. (b) vc = in.
The simply supported beam consists of a W21x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in."]. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.5 kips/ft, determine: (a) the beam deflection vA at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, LBc = 7 ft, LcD= 7 ft, LDE = 7 ft. 11111111公彩 B. C LAB LBC LCD LDE Answers: (a) VA= in. -19.406, (b) vc 2.016 in.
Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are , = 350 MPa (wire), and t-300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? D 90 mm 20° 100 mm View a-a of B P = 2 kN
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I=843 in.*]. Assume that the support at D can provide resistance either up or down. For a loading of w=4.8 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB= 12 ft. LBC = 8 ft. LcD=8 ft. LDE = 6 ft. W' B LAB Answers: (a) VA- i (b) vc= i Lac D LCD in. in. LDE E
X Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.4). Assume that the support at D can provide resistance either up or down. For a loading of w = 7.5 kips/ft, determine: (a) the beam deflection va at point A. (b) the beam deflection vc at point C. Assume LAB = 10 ft, LBC = 5 ft, LCD=5 ft, LDE= 6 ft. D LAB LBC LCD LDE Answers: (a) VA = 10.03 in. (b) vc = -1.197 in.
A beam is subjected to equal bending moments of Mz = 3600 N-m. The cross-sectional dimensions are b = 170mm c = 27 mm, d = 65 mm, and t = 5 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stres is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“1. Assume that the support at D can provide resistance either up or down. For a loading of w = 7.2 kips/ft, determine: (a) the beam deflection Va at point A. (b) the beam deflection vc at point C. Assume LAB = 11 ft, Lec = 6 ft, LcD = 6 ft, LDE = 5 ft. В D E LAB LBC LCD LDE Answers: (a) VA = 0.9 in. (b) vc = 0.5| in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1770 in.4]. For the loading shown, determine: (a) the bearn deflection at point.A. (b) the bearn deflection at point B. Assume MA = 250 kip-ft, P = 26 kips, LAB = 6.0 ft, Lec=9 ft. P MA В LAB LBC Answer: (a) VA = in. (b) VB = in,
The top of the folding workbench has a mass of 38 kg with mass center at G. Calculate the magnitude of the force supported by the pin at E. 690 mm- G. D B 230 mm F H. 990 mm 1070 mm Answers: E = N
An assembly of bars are designed in Figure 1. The assembly is made of structural A-36 steel where bar AB and BC has a drameter of 50 mm. ASTM and 25 mm The respectively. determine дар between C and the rigid wall at D is initially 0-15 mm, the support reaction at A and D when the force P= 292 kN is applied at B 600mm 450mm 292- A B D