I need the answer as soon as possible 10. The tensile strengths of stainless steel cables of different diameters are investigated to givefollowing results.Cable diameter (x):1.62.43.61.21.32 2.53Tensile Strength(y):5.288.34Use Lagrange's interpolation to compute the tensile strength of a cable of diameter 2.Ans. 3.892

Introduction: An algebraic declaration with one or greater phrases is known as a polynomial. A…

Answered: 10. The tensile strengths of stainless…

College Algebra

1st Edition

ISBN:9781938168383

Author:Jay Abramson

Publisher:Jay Abramson

Chapter3: Functions

Section3.3: Rates Of Change And Behavior Of Graphs

Problem 44SE: At the start of a trip, the odometer on a car read 21,395. At the end of the trip, 13.5 hours later,...

See similar textbooks

Similar questions

At the start of a trip, the odometer on a car read 21,395. At the end of the trip, 13.5 hours later, the odometer read 22,125, Assume the scale on the odometer is in miles. What is the average speed the car traveled during this trip?
Solve these prism and cylinder exercises. Where necessary, round the answers to 2 decimal places unless otherwise specified. A solid right cylinder 9.55 centimeters high contains 1910 cubic centimeters of material. Compute the cross-sectional area of the cylinder.
Explain the difference between the average rate of change of y as x changes a to b, and the instantaneous rate of change of y at x=a
2. Three tensile tests were carried out on an aluminum bar. In each test, the strain was measured at the same values of stress. The results were Stress (MPa) 34.5 69.0 103.5 138.0 Strain (Test 1) 0.46 0.95 1.48 1.93 Strain (Test 2) 0.34 1.02 1.51 2.09 Strain (Test 3) 0.73 1.10 1.62 2.12 Where the units of strain are mm/m. Use linear regression to estimate the modulus of elasticity of the bar (modulus of elasticity = stress/strain). %3D
Shortleaf Pines. The ability to estimate the volume of a tree based on a simple measurement, such as the diameter of the tree, is important to the lumber industry, ecologists, and conservationists. Data on volume, in cubic feet, and diameter at breast height, in inches, for 70 shortleaf pines was reported in C. Bruce and F. X. Schumacher’s Forest Mensuration (New York: McGraw-Hill, 1935) and analyzed by A. C. Akinson in the article “Transforming Both Sides of a Tree” (The American Statistician, Vol. 48, pp. 307–312). The data are provided on the WeissStats site. a. obtain and interpret the standard error of the estimate. b. obtain a residual plot and a normal probability plot of the residuals. c. decide whether you can reasonably consider Assumptions 1–3 for regression inferences met by the two variables under consideration.
c) The relationship between stress (o), force (F) and area (A) acting on an object is given as F O = A UNIVERSITI TEKNOLOGI MALAYSIA Find the maximum percentage error in calculating stress, if the max- imum percentage error in calculating force and area are 2% and 1% respectively.
From the following figure find the average value of n circumference ( cm )vs diameter 30 y = 3.3466x + 0.0319 20 10 2 5 6. 7 8 Select one: а. 3.346 b. 3.143 С. 3.14 d. 2.41 e. 0.2975 00
In last week's assignment, you calculated mean free path, total absorption, and reverberation time for a room that is 4 m long, 7 m wide, and has a ceiling height of 3 m. The floor is hardwood, = .15 at 500 Hz. The walls are gypsum wallboard (GWB), = .30 at 500 Hz. The ceiling is acoustic ceiling tile (ACT), = .95 at 500 Hz. 3) f a person speaking produces a sound power level of 70 dB, how much sound pressure level would you expect at a distance of 3 m?
c) The relationship between stress (o), force (F) and area (A) acting on an object is given as F A Find the maximum percentage error in calculating stress, if the max- imum percentage error in calculating force and area are 2% and 1% respectively.
Q.4/| In a measurement of a cylindrical shaft , an error in its diameter of 3% was made .Find the percentage error in its weight.
I want to examine the relationship between gas mileage of cars and the engine size (displacement in cubic inches). Which explanatory variable is Engine size Gas mileage Relationship between the two Both engine size and gas mileage Neither engine size nor gas mileage
Can you use OLS to estimate B the model y; = e? Yt

SEE MORE QUESTIONS

Recommended textbooks for you

College Algebra

Algebra

ISBN:

9781938168383

Author:

Jay Abramson

Publisher:

OpenStax

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Calculus For The Life Sciences

Calculus

ISBN:

9780321964038

Author:

GREENWELL, Raymond N., RITCHEY, Nathan P., Lial, Margaret L.

Publisher:

Pearson Addison Wesley,

College Algebra

Algebra

ISBN:

9781938168383

Author:

Jay Abramson

Publisher:

OpenStax

Mathematics For Machine Technology

Advanced Math

ISBN:

9781337798310

Author:

Peterson, John.

Publisher:

Cengage Learning,

Calculus For The Life Sciences

Calculus

ISBN:

9780321964038

Author:

GREENWELL, Raymond N., RITCHEY, Nathan P., Lial, Margaret L.

Publisher:

Pearson Addison Wesley,

Algebra: Structure And Method, Book 1

Algebra

ISBN:

9780395977224

Author:

Richard G. Brown, Mary P. Dolciani, Robert H. Sorgenfrey, William L. Cole

Publisher:

McDougal Littell

SEE MORE TEXTBOOKS

10. The tensile strengths of stainless steel cables of different diameters are investigated to give following results. Cable diameter (x): 1.2 1.6 2.4 3.6 Tensile Strength(y): 1.32 2.53 5.28 8.34 Use Lagrange's interpolation to compute the tensile strength of a cable of diameter 2. Ans. 3.892