14- In a diesel engine, the fuel is ignited bya) sparkb) injected fuelc) heat resulting from compressing air that is supplied forcombustion15- Which of the following is not an internal combustion enginea) 2-stroke petrol engineb) 4-stroke petrol enginec) diesel engined) gas turbinee) steam turbine

As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Answered: 14- In a diesel engine, the fuel is…

14- In a diesel engine, the fuel is ignited by a) spark b) injected fuel c) heat resulting from compressing air that is supplied for combustion

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. In 4-stroke CI engine the intercooler is recommended since it: a) Increases the ignition delay significantly. b) Decrease the ignition delay significantly. Increase the mean adiabatic flame temperature. d) Decreases the mean adiabatic flame temperature. e) None. c)
A boiler firing 30 gal/hr No. 6 oil (Heavy oil) requires 18.5 % excess air for complete combustion. Approximately, how many CFM of combustion air should be supplied ? Note: I don't understend what to do with the 18.5% excess air Note: I've asked this question twice before, but one gave "b)", and the other gave "c)" as the answer a) 450 CFM b) 750 CFM c) 900 CFM d) 1150 CFM
B.) the net work per cycle per cylinder and the thermal efficiency of the cycle c.) the mean effective pressure d.) power output for an engine speed of 3000 rpm
True or False: a.) For a mixing chamber, its conservation of mass principle requires that the sum of the incoming mass flow rate equal the volume mass rate of the outgoing mass. b.) The flow work is different for fluid pushed into and out of the control volume. c.) Cp is the sum of Cv and R d.) Mass flow rate can be expressed as mass equals density times velocity
1. A steam power plant works on a) both work on Rankine cycle b) both work on Brayton cycle c) Brayton cycle, Rankine cycle d) Rankine cycle, Brayton cycle and a gas-turbine power plant works on 2. In the regenerator of a gas-turbine power plant, a) temperature of air leaving the compressor is raised b) temperature of air leaving the turbine is raised c) both of the mentioned d) none of the mentioned 3. In gas-turbine power plant, by using a regenerator, a) efficiency increases, work output decreases b) both efficiency and work output increases c) efficiency increases, work output remains unchanged d) efficiency remains same, work output increases 4. In hydro-electric power plant, surge tank is for the protection of a) dam b) reservoir c) penstock d) powerhouse 5. The primary sources of energy are, a) coal, oil, uranium b) solar, wind, water c) hydrogen, oxygen, water d) wind, biomass, geothermal 6. The modern steam turbines are a) impulse turbine b) reaction turbine c)…
Q1) What is the meaning of chemical reaction? Write an example of a chemical reaction Q2) Mention the basic flame types and write an example of each type Q3) Compare between wood, lignite and peat in terms of carbon content and calorific value Q4) A small, low emission, stationary gas turbine engine operates at full load (3950 KW) at an equivalence ratio of 0.286 with an air flowrate of 15.9 kg/s. The equivalent composition of the fuel (ethane) is C2 H6. Determine the fuel mass flowrate and the operating air-fuel ratio for the engine. Q5) A gas-stream at 1 atm contains a mixture of CO, CO2 and N, in which the CO mole fraction is 0.15 and the CO2 mole fraction is 0.25. The gas-stream temperature is 1100K. Determine the absolute enthalpy of the mixture on both a mole basis and a mass basis. Also, determine the mass fractions of the three component gases
Enumerate the advantages and disadvantages of the following types of engine: a) Four-stroke engineb) Two-stoke enginec) Rotary or Wankle engine
10. compressive heating occurs within the combustion process in SI engines due to: a) Increasing the compression ratio b) Increasing fuel-air mixture temperature c) Increasing the ignition delay d) All of the above. e) None
Q4) Diesel engine four stroke, five cylinder operating at air fuel ratio 14.5 and engine time is 6.9 *10.5,^-5 sec/deg. Fuel injection occurs from 20° BTDC to 5° ATDC. The engine has a volumetric efficiency of 0.95 with fuel equivalence ratio of 0.8 and mass of air=718g. Calculate 1) displacement volume. 2) RPM. 3) time for one injection. 4) fuel flow rate through an injector. * Vd=62 litter , RPM= 2400, t= 0.00137sec/injection mf=22.9 g Vd=64 litter, RPM= 2400, t= 0.00137sec/injection mf=22.9 g Vd=64 litter, RPM= 2420, t= 0.00137sec/injection mf=22.9 g Vd=64 litter, RPM= 2400, t= 0.0137sec/injection mf-22.9 g Vd=64 litter, RPM= 2400, t= 0.00137sec/injection mf=22.5 g
7 - In the ideal Diesel cycle, the highest temperature of the air is 2241 K, the compression ratio is 17, and the pre-expansion ratio is 2.2. Assuming the specific heats are constant, which of the following is the temperature of the air at the exhaust outlet? a) 1045.8K B) 889.4K NS) 989.1K D) 814.2K TO) 1119.7 K
intake valve v) vi) intake compression How Tuel injector power lo egiteqo190 the number of molecules in the cylinder the internal energy of the gas; the work done on or by the gas; the thermal energy exchanged with the environment. exnaust vaive The diagrams show the cylinder of a petrol engine in 4 stages. Petrol vapour and air are drawn into the cylinder, The mixture is then squeezed together, and then exploded by a spark. The explosion pushes down the piston. The exhaust gases are then expelled from the cylinder. pril Use the first law of thermodynamics to analyse the energy changes during the process. At each stage explain what happens to the gas exhaust 0101
The stroke volume of a 4-stroke, 4-cylinder, water-cooled, electronically fired engine operating according to the Otto cycle is 1796 cm³, compression ratio 10, cylinder diameter 80,6 mm and connecting rod length 137 mm. This engine operating at 3000 rpm with 15 KMA ignition advance;a) Combustion chamber volume (dead volume)b) Average piston speedc) Find the position of the piston in relation to the upper dead point at the time of ignition.