16. A Diesel Cycle has a volume displacement of 0.95 m³ and the volume at during heat rejection is 1 m³. Determine the volume at the end of heat addition if the cut-off ratio 2.25. a. 0.21 m³ b. 0.11 m3 c. 0.25 m³ d. 0.15 m³ 17. Which statement is TRUE? a. Compression ratio is lesser than Cut-off ratio b. Volume at the end of compression is equal to the volume at the end of heat rejection c. Volume at the start of compression is equal to the volume at the end of expansion d. The highest temperature of the cycle is at the end of compression

16. A Diesel Cycle has a volume displacement of 0.95 m³ and the volume at during heat rejection is 1 m³. Determine the volume at the end of heat addition if the cut-off ratio 2.25. a. 0.21 m³ b. 0.11 m3 c. 0.25 m³ d. 0.15 m³ 17. Which statement is TRUE? a. Compression ratio is lesser than Cut-off ratio b. Volume at the end of compression is equal to the volume at the end of heat rejection c. Volume at the start of compression is equal to the volume at the end of expansion d. The highest temperature of the cycle is at the end of compression

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data refer to a 12-cylinder, single-acting, two-stroke marine diesel engine:Speed: 150 rpmCylinder diameter: 0.8mStroke of piston: 1.2 mArea of indicator diagram: 5.5x 10-4 m2Length of diagram: 0.06 mSpring value: 147 MPa per mFind the net rate of work transfer from the gas to the piston in kW.
a ull 36 ull zain IQ Asiacell 7:1A IC K/s HW9-2.jpg HW9-2 The rc (cutoff ratio) expression, which derived to form as qin * R (1+): (T, rk-1) B (Ctrl) for an air-standard Diesel cycle. D
b- A 4-stroke diesel engine is to be designed to operate with the following characteristics at sea level, where the ambient conditions are 103 kPa and 10°C. b.p=260 kW, s.f.c=0.244 kg/kW.h, Speed = 1500 rpm, volumetric efficiency = 0.78, A/F ratio = 17:1. Calculate the required engine capacity and the anticipated bmep. The engine is fitted with a supercharger so that it may be operated at an altitude of 2700 m where the atmospheric pressure is 73 kPa. The power taken by the supercharger is 8% of the total power produced by the engine and the temperature of the air leaving the supercharger is 32°C. The A/F ratio and thermal efficiency remain the same, so as the nv Calculate the increase of pressure at the supercharger to maintain the same net power output. Take R = 0.287 kJ/kg.K.
Show all sets of equations belonging to two-time ideal diesel cycle and two-time ideal mixed cycle by creating P-V diagrams as well.
1- A four-cylinder, two stroke cycle diesel engine with (10.9 cm) bore and (12.6 cm) stroke produces (88 kW) of brake power at (2000 RPM). Compression ratio is (18:1). Determine: (a) Engine displacement. Ans.: (4700.6 cm³). (b) Brake mean effective pressure. Ans.: (561.7 kPa).
Task 1: Your first customer asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report which includes the following steps: Evaluate the performance of a four-stroke, eight cylinder ideal Diesel cycle with a cylinder bore of 10 cm and a piston stroke of 12 cm when it is operated at 2200 rpm and 4 the air temperature at the beginning of compression prosses is 40 °C if the minimum volume enclosed in the cylinder is 5 percent of the maximum cylinder volume and the cut-off ratio is 1.7 by determining the delivered power from the engine and it's efficiency and comparing your answer if the engine is changed to be two stroke engine.
HANDWRITTEN AND THE FINAL ANSWER SHOULD BE IN ENGLISH SYSTEM Lycoming TIO-5XX engine is a turbocharged, fuel-injected, horizontally opposed, six-cylinder aircraft engine featuring three cylinders per side, manufactured by Lycoming Engines. Engr. Chua would like to improve the engine process changing the paddle work supplied by the turbocharger to 1,550 ft-lbf. The experimental engine cylinder has 550 liters with an initial parameters of 2350 psf and 510 R to a final temperature of 1150 R. Consider a constant volume process. What is (a) the change in internal energy and (b) heat, if the specific heat ratio is 1.338.
PARTS A & B ( Read and Solve carefully) At the beginning of the compression process of an ideal Diesel cycle operating with the compression ratio r = 18.1, the temperature is T1 = 300K and the pressure is P1 = 0.1MPa. The temperature at the end of the combustion process (the highest temperature of the cycle) is T3 = 1800 K. Evaluate the cutoff ratio rc and the heat delivered during the combustion process qin (in kJ per kg of air) using PART (A) - air standard (variable specific heat) PART ( B) - cold-air standard (constant specific heat evaluated at room temperature). which result, (a) or (b), more accurately represents the actual process in a diesel engine??
4. The efficiency of an Otto cycle is 50% and y is 1.5. What is the compression ratio ? [Ans. 4]
2. A four-cylinder 2.5 L spark-ignited engine is mounted on a dyno and operated at a speed of W=3000 rpm. The engine has a compression ratio of 10:1 and mass air--fuel ratio of 15:1. The inlet air manifold conditions are 80 kPa and 313 K. The engine produces a torque of 160 Nm and has a volumetric efficiency of 0.82. (a) What is the brake power Wb (kW)? (b) What is the brake specific fuel consumption bsfc (g/kWh)?
thermodynamics: Otto Cycle operates on 0.1 kg/s of air from 10 psi and 340 Kelvin at the beginning of compression. The temperature at the end of combustion is 5000 deg R; compression ratio is 8 and k = 1.30. Compute Qa, Qr, W, e and the pressure and temperature at the end of expansion
Sketch the P-V diagram of the Internal Combustion Engine showing the ideal cycles of a DieselEngine. Label the events.