160Chapter 6: Hydraulic Conductivity6.8 The hydraulic conductivity, k of a soil is 0.832 x 10-5 cm/sec at a temper-ature of 20°C. Determine its absolute permeability at 20°C, given that at20°C y = 9.789 kN/m³ and n = 1.005 × 10 3 N-s/m² (Newton-second persquare meter).

Absolute permeability Kˉ=8.542×10−15m2Explanation:

Answered: 160 Chapter 6: Hydraulic Conductivity…

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Question

160
Chapter 6: Hydraulic Conductivity
6.8 The hydraulic conductivity, k of a soil is 0.832 x 10-5 cm/sec at a temper-
ature of 20°C. Determine its absolute permeability at 20°C, given that at
20°C y = 9.789 kN/m³ and n = 1.005 × 10 3 N-s/m² (Newton-second per
square meter).

Expert Solution

Step by step

Solved in 1 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A constant head test is performed using a permeameter in the laboratory. The graduated cylinder collects 892 cm3 of water in 112 seconds. The soil specimen diameter = 18 cm , th elevation of water in upper-most piezometer is 181 com , the elevation of water in lowest piezometer is 116.6 cm and the piezometer inlets are evenly spaced at 16.7 cm on center. Compute the hydraulic conductivity, k and choose the correct answer below based on that. O A. 2.1 x 10^-3 cm/second O B. 1.5 x 10^-2 cm/second O C. 2.91 x 10^-2 cm/second O D. 2 x 10^-2 cm/second QUESTION 10 Given: -Applied stress on a soil = 122 kPa %3D -Influence Factor = 0.4 Compute the change in stress at 10 m below the edge of 25 m dimeter oil tank and select the correct answer from below: O A. Change in stress = 44 kPa O B. Change in stress = 49 kPa O C. Change in stress = 40 kPa O D. Change in stress = 42 kPa %3D
A soil sample is placed in a 1m long and 10cm diameter tube. A constant supply of water is allowed to flow from inlet to outlet. The total water head at the inlet is 2m and the total water head at the outlet is 1m. The hydraulic conductivity is 0.001 cm/s. Which of the following answer is correct? O a. The flow velocity is 0.001 cm/s Ob. The flow velocity is 25 cm/s c. The hydraulic gradient in the tube is 2 Od. The hydraulic gradient in the tube is 0.001
29. Soil in a field has three layers. Each has a thickness of 3m, 4m, and 3m, from top layer to bottom layer. The hydraulic conductivity of each layer is 0.0043cm/s, 0.0072cm/s, and 0.0018cm/s, respectively. Calculate the effective horizontal hydraulic conductivity.
Three soil samples in a permeameter overlie one another with their characteristics listed below. Layer Hydraulic Conductivity, ft/day Length of aquifer, ft 1 10 5 2 0.20 3 0.030 12 a. Determine the equivalent hydraulic conductivity, in ft/day, if the flow is perpendicular to the stratification. b. If a falling head test is used, calculate the time required, in seconds, for the head to drop from 65 to 54 ft. The cross-sectional area of the permeameter and the standpipe are 300 square feet and 30 square feet respectively.
(b) TABLE Q1(b) shows three layers of soil used in permeability pilot test. (i) Calculate the average vertical conductivity of the soil in cm/day. (ii) Calculate the transmissivity of the soil when water is at the ground surface. (iii) Discuss the factors that might affect the results obtained in Q1(b)(i) and Q1(b)(ii).
← Darcy' Law A sand sample of 35 m² cross sectional area and 20 cm long was tested in a constant head permeameter. Under a head of 60 km, the discharge was 120 ml in 6 min. The dry unit weight of sand used for the test was 1120 g. and GS = 2.68 Take Sw = 1 g/ cm³ The hydraulic conductivity (in cm/sec) is × 10-³ X
Water is flowing through three soil layers as shown in Fig. Q2. The cross-section is a square with sides of 100 mm. The hydraulic conductivity (also known as coefficient of permeability) of each soil layer is given in Table Q2. a. What is the equivalent hydraulic conductivity of the three layers? b. Determine the flow rate exiting the system. c. Determine the elevation head diagram, the total head diagram, and the pressure head diagram from point A to point B. Ah = 30 cm h, = 50 cm h2 = 20 cm B D = 10 cm 3.33 cm 3.33 сm 3.33 cm O Datum 45 cm O Datum Fig. Q2: Three-layer permeameter
For a falling head permeability test, these valueare given: Length of the soil specimen = 200 mm Area of the soil specimen = 1000 mm2 Area of the standpipe = 40 mm2 Head difference at time, t = 0 min is 500 mm Head difference at time, t = 3 min is 300 mm1. Determine the hydraulic conductivity of thesoil in cm/sec.2. What was the head difference at time, t =100 sec?
Assuming the groundwater table is at ground surface and the soil bulk unit weight is 20kN/m3. At 2m depth below ground level. The pore water pressure is approximately: O a. 19.6 kPa O b. 9.8 kPa O c. 200 kPa O d. 98 kPa
SITUATION 4 The soil under a dam has three layers with different coeffident of permeability. Determine the following: (a) Calculate the equivalent hydraulic conductivity in am/sec. (b) Compute the Transmissibility of the soil when the water table is at the ground surface, in sq.cm/ sec (Note: Transmissibility= k x distance) (c) Determine the seepage velocity of water moving through soil if it has a void ratio of 0.60 and a hydraulic gradient of 0.0018 in cm/hr. Illustration for Situation 4 KI = 0.000 I0 cm/sec at 3m K2= 0.032 cm/sec at 4m K3= 0.000041 cm/sec at Gm
P 4: A sand sample of 35cm2 cross sectional area and 20cm long was tested in a constant head permeameter. Under a head of 60cm, the discharge was 120ml in 6min. The dry weight of sand used for the test was 1120g, and G3=2.68. Determine (a) the hydraulic conductivity in cm/s, (b) the discharge velocity, and (c) the seepage velocity. Answers: a) 3.174 x 103 cm/s, b) 9.52 x 10³ cm/s, c) 2.36 x 10-² cm/s
A sample of sand, 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a constant-head apparatus. The total head was kept constant at 30 cm and the amount of water collected in 5 seconds was 40 cm^3. The test temperature was 20 deg C. Calculate the hydraulic conductivity. Provide a diagram a.5.0 x 10^-2 b.3.47 x 10^-2 c.2.0 x 10^-1 d.6.7 x 10^-1

SEE MORE QUESTIONS

Recommended textbooks for you

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning