F7-7. Two klentical 20-mm thick plates are bollad to thetop and bottom lange to form the buili-up heam. II thebeam is subjected toa shear force of V = 300 KN, determinethe allowable maximum spacing s of the boits to the nearestmm. Each bolt has a shcar strength of 30 RN.F7-9. The boards are boltod together to form the bull-upheam. Ir the beam is suhjactad to a shear force of V = 15 kip.determine the allowahle maximum spacing of the bolts lethe nearst in. Each bolt has a shear strength of 6 kip.I in 05 in.200 mm3 in.10 m300 mm10 mm20 mm7-9FL7

Given data:- shear force = 300KN shear strength of each nail = 30 KN find the spacing between the…

17-7. Two klentical 20-mm thick plates are bollod to the top and bottom flange to form the buli-up heam. II the beam is subjected to a shear force of V = 300 KN, determine the allowable manimum spacing s of the boits to the nearest mm. Each bolt has a shcar strength of 30 RN. 200 mem 20 mim 10 mem 300mm i0 mm 10 mam 20 mim 17-7

17-7. Two klentical 20-mm thick plates are bollod to the top and bottom flange to form the buli-up heam. II the beam is subjected to a shear force of V = 300 KN, determine the allowable manimum spacing s of the boits to the nearest mm. Each bolt has a shcar strength of 30 RN. 200 mem 20 mim 10 mem 300mm i0 mm 10 mam 20 mim 17-7

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7-67. If the allowable shear stress for each of the 10-mm-diameter steel pins at A, B, and Cis Tllo - 90 MPa, and the allowable normal stress for the 13-mm-diameter rod is oalon - 150 MPa, determine the largest intensity w of the uniform distributed load that can be suspended from the beam. 1.2 m 0.3m
R7-3. Determine the required thickness of member BC and the diameter of the pins at A and Bif the allowable normal stress for member BC is Gallow allowable shear stress for the pins is Tallow- 70 MPa. - 200 MPa, and the 40 mm 24m 30 kN/m
PI-2. In cach case, determine the largest internal shear force resisted by the bolt. Include all nocessary free-body diagrams SKN 6EN 6RN 2 AN
The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 1 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet
The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in the bolts must be limited to 29 ksi, determine the minimum bolt diameter that may be used for this connection. Cocoo Answer: dmin= in.
The yoke-and-rod connection is subjected to a tensile force P. The end of the 40-mm diameter rod is embedded inside a wall at a length I of 100 mm using epoxy adhesive. If the allowable normal stress for the rods is 60 MPa, the allowable shear stress for the 25- mm diameter pin A is 50 MPa, and the allowable shear stress of the epoxy adhesive is 6 MPa, determine the largest force P that can be applied to the assembly. Note: Show your calculations for all types of stresses in detail. 40 mm 30 mm A 25 mm P.
The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (sb)allow = 2 ksi, and the allowable tensile stress within the bolt shank S is (st)allow = 18 ksi, determine the maximum allowable tension in the bolt shank. The bolt shankhas a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
7-63. The cotter is used to hold the two rods together. Determine the smallest thickness of the cotter and the smallest diameter d of the rods. All parts are made of steel for which the failure normal stress is oal - 500 MPa and the failure shear stress is Tail - 375 MPa. Use a factor of safety of (F.S.), - 2.50 in tension and (ES.), - 1.75 in shear. 30 kN Do mm 40 mm 30 kN
FI-15. Determine the maximum average shear stress developed in each 3/4-in.-diameler bolt. 10 klp 3 kip S kip FI-15
*7-52. The lapbelt assembly is to be subjected to a force of 800 N. Determine (a) the required thickness i of the belt if the allowable tensile stress for the material is (a)allow - 10 MPa, (b) the required lap length di if the glue can sustain an allowable shear stress of (Tallow)g - 0.75 MPa, and (c) the required diameter d, of the pin if the allowable shear stress for the pin is (7lo), - 30 MPa. 800 N 5 ma S00 N
The assembly consists of two sections of galvanized steel pipe connected together using a reducing coupling at B. The smaller pipe has an outer diameter of 0.75 in. and an inner diameter of 0.68 in., whereas the larger pipe has an outer diameter of 1 in. and an inner diameter of 0.86 in. If the pipe istightly secured to the wall at C, determine the maximum shear stress in each section of the pipe when the couple is applied to the handles of the wrench.
The long bolt passes through the 70.4-mm-thick plate. If the force in the bolt shank is 9.5 KN, then the average shear stress (MPa) along the cylindrical area of the plate defined by the section lines a-a is: O a. 0.00 O b. 21.00 O c. 2.39 O d. 4.77 O e. 1.19 18 mm b b 8 mm Time left 0:45:52 a 7 mm YouTube The wood beam has an allowable shear stress of 15 MPa, the maximum shear force V (kN) that can be lind to the cross section is: