1/9 A space shuttle is in a circular orbit at an altitude of 200 mi. Calculate the absolute value of g at this altitude and determine the corresponding weight of a shuttle passenger who weighs 180 lb when stand- ing on the surface of the earth at a latitude of 45°. Are the terms "zero-g" and "weightless," which are sometimes used to describe conditions aboard orbit- ing spacecraft correct in the absolute sense?

1/9 A space shuttle is in a circular orbit at an altitude of 200 mi. Calculate the absolute value of g at this altitude and determine the corresponding weight of a shuttle passenger who weighs 180 lb when stand- ing on the surface of the earth at a latitude of 45°. Are the terms "zero-g" and "weightless," which are sometimes used to describe conditions aboard orbit- ing spacecraft correct in the absolute sense?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.20P: Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of...

See similar textbooks

Similar questions

Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.
Required information A photograph of the NASA Apollo 16 Lunar Module (abbreviated by NASA as the LM) is shown on the surface of the Moon. Such spacecraft made six Moon landings during 1969 - 72. A simplified model for one of the four landing gear assemblies of the LM is shown. Assume the weight of the LM is uniformly supported by all four landing gear assemblies, and neglect friction between the landing gear and the surface of the Moon. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A (2.5, 2.5, -2.2) m B (1.5, 1.5,0) m C(2, 1,-1.2) m D(1,2,-1.2) m Z B D If the LM has 14950 kg mass and rests on the surface of the Moon where acceleration due to gravity is 1.62 m/s2, determine the forces supported by members AB, AC, and AD. (Round the final answers to four decimal places. Include a minus sign if necessary.) The forces supported by members AB, AC, and AD are as follows: TAB 10621 N TAC= 2903 N TAD 6032 N
Two blocks are connected by a (massless) string that passes over a (massless, frictionless) pulley as shown. Assume the interface between block A and the horizontal tabletop to be frictionless. pulley If mA = 6.3 kg and mg = 8.8 kg, what is the tension in the string? Express your answer in N, to at least one digit after the decimal point.
From rest a balloon begins to rise. the Balloon experiences a lift due to a buoyant force of 8000 N. 1. Total massof the balloon is 600kg. Find Acceleration. 2. The balloon rises a distance of 10m and loses a mass of 50 kg after a weight is thrown off. Find the acceleration of the balloon after this weight loss 3. Find the initial velocity of the mass in the vertical direction at the timeof the jump. 4. After falling 10 m, find the mass' final velocity as it comesinto contact with the ground. 5.What is the total time the mass takes to hit the ground? 6. Find the heightof the balloon when the mass hits the ground 7. The mass lands 3 m from the baloon, find the horizontal velocity required to land 3m from the balloon. 8. Since the balloon exeperiences equal forces when the mass is thrown off, what is the horizontal velocity the baloon experiences during this act and how far does the balloon travel when the mass comes into contact with the ground?
The input piston and output plunger of a hydraulic car lift at the same level, as shown in the drawing. The cross-sectional area of the input piston is 12cm^2, while that of the output plunger is 1200cm^2. The force F1 is applied to the input piston had a magnitude of 150 N. What is the weight W of the car? Neglect the weight of the piston and plunger.
A 210-kg mass is supported as shown. Calculate the angle a and the force P. (Neglect friction in all pulleys) В 20 210 kg
A rock is attached to the left end of a uniform meter stick that has the same mass as the rock. In order for the combination of rock and meter stick to balance atop the triangular object in Fig., how far from the left end of the stick should the triangular object be placed? (i) Less than 0.25 m; (ii) 0.25 m; (iii) between 0.25 m and 0.50 m; (iv) 0.50 m; (v) more than 0.50 m.
Q2/ A former student of mechanics wishes to weigh himself but has access only to a scale A with capacity limited to 100 1 shown he discovers that when he exerts a pull on the rope so that B registers 19 lb, the scale A reads 67 lb. What is his correct weight? and a small 20-lb spring dynamometer B. With the rig В
Determine the distance h for which the spacecraft 5 will experience equal attractions from the earth and from the sun. Use Table D/2 of Appendix D as needed. Assume L = 155 000 km. Sun Answer: h= i Not to scale Earth (105) km
pls send me answer of this question all the parts pls and i will rate you sure, pls solve a,b,c and d and also a and b A 200-kg dragster (racing car) exerts a constant force of 4000 N during a race. The coefficient of kinetic friction between the tires and the pavement is .15. If the drag strip is 1000 m long, determine:a. The net force on the dragster. b. The acceleration of the dragster. c. The time it takes for the dragster to finish the race.d. The dragster's velocity at the end of the race.The dragster now needs to slow down, so it opens a parachute. The force of air drag is 3500 N. The driver also locks the brakes of the dragster, and the coefficient of kinetic friction becomes .75. Determine:a. How long it will take to stop the dragster.b. The distance the dragster travels while stopping.
Three identical steel balls, each of mass m=80kg, are placed in the cylindrical ring which rests on a horizontal surface and whose height is slightly greater than the radius of the balls. The diameter of the ring is such that the balls are virtually touching one another. A fourth identical ball is then placed on top of the three balls. Determine the force P (in N, roundoff to 2 decimal places exerted by the ring on each of the three lower balls.
A crane is lifting a system with a constant speed. The weight of each object is shown. Neglect the mass of the cables. Note that K stands for Kipps [1K = 1,000lbs] and is a unit of force. Do NOT convert or multiply by g. cable 1 How many forces are acting on the ring? 4. ring (2K) 6 How many forces are acting on the spreader bar? cable 2 cable 3 How many forces are acting on the load? 3. 45° 45° Are the forces on the system balanced? yes v spreader bar (20K) cable 4 cable 5 How much tension in is cable 1? K How much tension in is cable 2? K load (48K) BARNHART K How much tension in is cable 3? K How much tension in is cable 4? K How much tension in is cable 5? check answers'