2 A Triac control of a three-phase, 30 kW, 400 V, 50 Hz, six-pole, star- connected squirrel-cage induction motor such that it operates at a full load efficiency of 0.85 p.u. and power factor 0.8 lagging. Calculate the average and rms current rating and maximum voltage rating required of the triacs.

Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
icon
Related questions
icon
Concept explainers
Question
I need answer within 20 minutes please please with my best wishes
2 A Triac control of a three-phase, 30 kW, 400 V, 50 Hz, six-pole, star-
connected squirrel-cage induction motor such that it operates at a full load
efficiency of 0.85 p.u. and power factor 0.8 lagging. Calculate the average
and rms current rating and maximum voltage rating required of the triacs.
[Ans : 32 A, 45 A, 326 V]
The motor in Problem 15.2 drives a load characterised by the relation
TL = k o where T, is the shaft torque and o is the motor speed. Operation
is required to give rated torque at rated speed of 960 rpm and also to
supply the appropriate load at speed of 640 rpm at which the power factor
is dropped to 0.6. If the motor operates at full voltage at its upper speed,
estimate roughly, the change of thyristor firing-angle necessary to achieve
satisfactory operation of the motor at the lower speed. Assuming that the
motor impedance is unchanged between the two speeds.
3
[ Ans: 37° <a<90°]
Transcribed Image Text:2 A Triac control of a three-phase, 30 kW, 400 V, 50 Hz, six-pole, star- connected squirrel-cage induction motor such that it operates at a full load efficiency of 0.85 p.u. and power factor 0.8 lagging. Calculate the average and rms current rating and maximum voltage rating required of the triacs. [Ans : 32 A, 45 A, 326 V] The motor in Problem 15.2 drives a load characterised by the relation TL = k o where T, is the shaft torque and o is the motor speed. Operation is required to give rated torque at rated speed of 960 rpm and also to supply the appropriate load at speed of 640 rpm at which the power factor is dropped to 0.6. If the motor operates at full voltage at its upper speed, estimate roughly, the change of thyristor firing-angle necessary to achieve satisfactory operation of the motor at the lower speed. Assuming that the motor impedance is unchanged between the two speeds. 3 [ Ans: 37° <a<90°]
Expert Solution
steps

Step by step

Solved in 3 steps

Blurred answer
Knowledge Booster
Thermistors
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Similar questions
  • SEE MORE QUESTIONS
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,