2. A load P is supported by two steel springs arranged in series as shown. The upper spring has 20 turns of 20mm diameter wire on a mean diameter of 150 mm. The lower spring consists of 15 turns of 10 mm diameter wire on a mean diameter of 130 mm. Determine the maximum shearing stress in each spring if the total deflection is 80 mm and G = 83 Gpa. Use exact method. 2244 you www.www.

2. A load P is supported by two steel springs arranged in series as shown. The upper spring has 20 turns of 20mm diameter wire on a mean diameter of 150 mm. The lower spring consists of 15 turns of 10 mm diameter wire on a mean diameter of 130 mm. Determine the maximum shearing stress in each spring if the total deflection is 80 mm and G = 83 Gpa. Use exact method. 2244 you www.www.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is placed 3 m from A. The brass (Ebrass = 85 GPa) rod has a cross section of 30 x 30 mm and the copper (Ecopper = 120 GPa) rod 20 x 20 mm. Determine the normal stress and deflection of both bars. 1.5 m 2 m B -copper 100 kN brass- 3m 3 m E
Question-6b, A leaf spring is required to have a span of 2.0 m. Determine the required thickness (in mm) of each plate if the maximum stress should not exceed 120 MPa and the maximum central deflection should not exceed 12 mm. (Take E 200 GPa)
PROBLEM 2: What torque can be applied without exceeding the shearing stress of 65 MPa in the botts? Bolt diameter = 12 mm 83 R₁ R2 R₁ = 200.5mm R₂ = 150.5mm 23 = 100.9mm
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
Determine the principal stresses acting at the 1 section using Mohr circle 150mm 5mm 5kN 60° 180mm 6mm 8mm 2 m 3 m 3 m 200mm