2. A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2.5 mm? is used to measure a horizontal distance of 85.95 meters supported at both ends. If the standard pull for the tape is 5.44 kg, what must be the applied pull in kg (normal tension) in order to have no correction at all. Use 9.81 m/s? as acceleration due to gravity.

2. A steel tape with a unit weight of 76.5 kN/m³ and having a cross-sectional area of 2.5 mm? is used to measure a horizontal distance of 85.95 meters supported at both ends. If the standard pull for the tape is 5.44 kg, what must be the applied pull in kg (normal tension) in order to have no correction at all. Use 9.81 m/s? as acceleration due to gravity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select the graph showing Tmax versus D1 after answering the question.
Question 4 List the steps in details to draw the shape below using AutoCAD commands 190 220 50 -90 - 50 114 81 R80 450 122 -R125 68 65 290 50 290 630
antuitive methodology (seize and fox) noting they will be different. olowing cases, find the degrees-of-freedom using KMOGE (Identify L. h. Jz and M) and using the em 3: KMOGE has conditions under which it simply produces the wrong answer. In each of the A. L= Mseize and Fix B L = MKMOGE = Mseize and Fix J = MEMOGE Msetze and Fix
Question The following fiqure shows the position # 9 tigure shows the vs time attoched' to the end of a plot t of an 80mass The apring. the position is geven in meters and time in secands. The phasc angle is ? 0.4 (0.0.2427) 0.2 (0.7469, 0) (0.027.0) 04 0.6 0.8 t (s) -0.2 ( m)
QI: Draw the orthographic Projections of given object. 20,2620 R20 2/3 35 35 06
POLAR COORDINATES: PLS SHOW COMPLETE SOLUTION. SOLVE IT BY HANDWRITTEN. ANSWERS SHOULD BE ROUND OFF TO FOUR SIGNIFICANT FIGURES.
Please Fill In the blanks where I have marked red X's using the questions and Image below. 1. On the drawing above, before any geometric controls are applied, what is the coaxility tolerance is implied between the diameters? 2. On the part above, apply datum feature symbols to create a datum axis A-B by using the right and left diamters. 3. Apply a position coaxility between the right and left diamter of 0.1 at MMC. 4. Apply a position tolerance to the large center diameter within a diameter of 0.3 in relation to the single datum axis established by both datum features A and B.
2:01 ul 4G 4. A sulms.su.edu.om While constructing a building, an engineer need to fix two steel beams together using a bracket as shown in Figure 1. Using absolute coordinate system, construct a G-code program for drilling hole number 3 only. To remove the metal chips the hole should be done in three equal steps. During the drilling, coolant should be on before spindle starts and stop after spindle stops. The spindle speed set to 1750 RPM. Drilling bit in rack number 2 and it should be 1 mm over the work piece. Drilling feed rate is 20 mm/min. Explain each code used in the program in a column 57.5- 12.5 Hole (4) Hole (3) 30 Hole (1) Hole (2) ΧΟ Υ0ΖΟ All dimensions shown are in mm Figure 1 B. -> 28 •..
Given: N1 = 10, N2 = 20, N3 = 30, N4 = 40 J1 = 1, J2 = 2, J3 = 3, J4 = 4, J5 = 5, D1 = 1, and D2 = 2 Determine: 01(s)/Tl(s) T₁(1) 0₁ (1) CC N₂ D2, J2 N₁ J₁. Di N3 J3 N4 N₂0 JS J4
QUESTION 12 Form the graph given in Figure Q12, the displacement for the time interval given form 6 - 8 seconds is: s (m) s = 108 108 s= 0.5 1 (s) 10 6. O A 864 m O B. 648 m OC. 432 m D. 216 m
An aircraft deigned for supersonic flight utilises a delta wing, as shown. Using the values given in the table for the labelled dimensions. Calculate the total wing span. Give your answer to 3 decimal places. C
Solve in MS excel using bisection and Newton-Raphson method! Show all steps in excel