2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EĞL and HGL. h2 Water T = 10°C (50°F) Globe valve

2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EĞL and HGL. h2 Water T = 10°C (50°F) Globe valve

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pump feeds 100,000 lbs/hr of mirbane oil @ a temp. of 68OF (sp.gr. = 1.21, µ=2.15 x 10-3 Pa-s) from a tank @ atmospheric pressure into a reactor where a gauge pressure of 0.1 atm. is maintained. The pipeline is made of steel pipes with a diameter of 89 x 4 mm (o.d. x thickness) having a insignificant corrosion. The equivalent length of the pipeline is 45 m. The pipeline is provided with an orifice (d.o. = 51.3 mm), 2 gate valves (before & after pump, and 4 pipe bends @ an angle of w/a bending radius of 160 mm. The liquid is lifted to a height of 49.32 ft. What is the Total friction losses (in meter) = Theoretical power (kW) = Elevation head =
1. A 1.5” S40 pipe has a capacity of ______ cu. ft/sec. at a 1 ft/sec. velocity. A. 0.0031 B. 1.7672 C. 0.0332 D. 0.0123 2. The bulk density of impure alumina oxide in lb/ft3 is A. 0.70 B. 80 C. 90 D. 60 3. Tetrahydrofuran has a vapor pressure of ______ mmHg at 176 deg. F A. 200 B. 1518 C. 1173 D. 2 562
Draw HGL and EGL for the pipe shown in fig. Then Calculate the rate of flow through this pipeline and the pressures at A, B, C, and D. Neglect all losses. 20' [5' B 'C 6" Dia. 2" Dia.- 12' 8'
Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 0.020 B 488 102 0.032 C 1220 203 0.024 Good Luck -re (2) Water qure (3) EL=7om A B EL-15m
The two lines shown are the EGL and HGL of a pipeline. Which statement is true? A B D O There is a nozzle between Cand D The area of flow in AB is gradually decreasing There is turbine at C
Pipeline AB connects two reservoirs. The difference in elevation between the two reservoirs is 33 ft. the pipeline consists of an upstream section, D1= 30 in and L1 = 5000 ft and a downstream section, D2 = 21 in and L2 = 3500 ft. The pipes are concrete (f=0.016) and are connected end to end with a sudden reduction area. Compute the discharge capacity.
The pipe is 25mm with friction factor of 0.022. The second tank is vented. H1=1.4m H2=4.5m H3=1.0m X1=14.9m X2=2.7m Calculate the pressure(kPa) above the gasoline in the first tank that will result in a flowrate of 400 liters/min.
The pipe connection shown has a series parallel connection. The rate of flow in the pipe 1 is 300 liters per sec. Assuming equal values of f = 0.02 for all pipes. Compute the discharge of pipeline 2 in cu.m per sec. Compute the discharge of pipeline 3 in cu.m per sec. Compute the discharge of pipeline 4 in cu.m per sec.
Question 7 A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 120 (Hazen-Williams) Pipe 2 n = 0.020 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.
Methanol (SG = 0.8335, viscosity is equal to that of water) is being transported from a very large reservoir and is entering at a standard 1.25-in 540 pipe at an absolute pressure of 14.7 psia. The methanol is transported at a total of 1450 ft and passes through 15 standard ells, 5 gate valves (open), 6 tees (standard), and 4 tees (as ell, entering branch). The methanol is discharged 22 ft above the inlet at a gauge pressure of 8 psig. If the fluid flows at a rate of 30 gpm and the pump have an efficiency of 50%, calculate the actual power needed in kW.
Tow oil tanks are connected with a pip that has a constant radius, the readings of the two gauges and the elevations are as follow; p1 p2 z1 z2 Oil SG psi psi (ft) (ft) 40.4 95.7 56.8 68.2 0.8 Determine and justify the flow direction of oil in the pipe 2. 1.
a. Calculate the pump head b. Plot the EGL and HGL for the system