2. A uniform bar 12 m long and weighing 20N is hanged by means of a rope at point A and the loads are positioned as shown in the figure. a. Draw the force diagram. b. Determine the downward pull WL from the left end that is necessary to hold the bar in equilibrium? c. Determine the magnitude of the force exerted by the rope? LCEILING Figure ROPE 4m A

2. A uniform bar 12 m long and weighing 20N is hanged by means of a rope at point A and the loads are positioned as shown in the figure. a. Draw the force diagram. b. Determine the downward pull WL from the left end that is necessary to hold the bar in equilibrium? c. Determine the magnitude of the force exerted by the rope? LCEILING Figure ROPE 4m A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. A rigid bar AB, 9 m long is suspended by two vertical rods at its end A and B and hangs in a horizontal position by its own weight. The rod at A is brass, length 3m, cross-sectional area is 1000 mm? and E̟ =1×10°N/ mm? . The rod at B is steel, length 5 m , cross-sectional area is 445 mm?. At what distance 'd' from A may a vertical load P=300ON be applied if the bar is to remain horizontal even after the load is applied? ve stred Steel 5m Brass 3m P = 3000N B 9m
Question #3 The figure below shows a simple form of roof truss, freely supported at X and Y and carrying a vertical load of 2 kN at Z. Determine the reactions at X and Y and the force in each member, stating whether it is tension or compression. Use Lami's theorem. 10 m Z 2 kN ost > 2.5 m
The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? B. What is the value of the absolute maximum moment? C. Reinforcing steel bars [shown by the bold lines] are used in the concrete beam in the lookout as shown in the diagram below, which of the following diagrams best shows the placements of these reinforcements?
2) Figure 2 shows an arrangement of rigid beams connected via ropes(E = 50GPA, diameter = 10mm) to the roof of a building. All point loads are 10kN. The 10kN point load on KN works in the centre of the beam and on SO 1m from S. Determine: )The displacement of L and the rotation of beam RQ Cii The displacement of 0 and the rotation of beam KN (ij The displacement of N and the rotation of beam SO A D F 3m 3m B 1.5m 2.5m 0.5m 3m 2.5m 10KN 1.5m 10KN 3m 1.5m 1m K 2.5m 1m 2m 0.5m 1.5m 1.5m Figure 2
Problem II. The truss shown in the figure below is applied with force P (refer to the table of values for P). E 1.5 m 1.5 m A 1.5 m P (kN) P = 200kn 2 m 2 m- a. How much is the force in member DE (include whether tension or compression)? b. How much is the force in member BC (include whether tension or compression)? c. What is the greatest force P (different from the one given) that can be applied to the truss such that no member is subject to a force exceeding 2.50 kN in tension or 2 kN in compression?
Calculate the bar forces in the truss shown in the figure below using the knot method. 2 kN 45° A P = 4 kN 2 m E 2 m 2 m
The antenna tower shown is attached to the foundation by a ball and socket joint. It is supported in its upright position by four high strength AC, AD and AE. Given: Height of tower, h = 20 m Diameter of tower, d = 150 mm Diameter of steel wires = 6.5 mm Steel modulus of elasticity = 200 GPa Find the force in wire AD if a pulling force F = 5 kN acts along the x - axis at the tip of the tower. F 8.0m 12.0m 12:0m 12.0m 12.0m 12.0m
1. A truss is loaded as shown in the figure below. Determine the following: a) Vertical reaction at roller at A. Indicate the direction by writing an arrow next to your answer. (Example: = 12.34 kN 1) Ay b) Force in member BC. State whether the force is tension or compression (Example: FBC c) Force in member BE. State whether the force is tension or compression (Example: FBE = 12.34 kN (C) %3D 12.34 kN (T)) 6 KN 6 KN 6 kN Im 3 kN 3 kN 1.5 m 2m 2m 2m 2m
25 mm An eccentric force P is applied as shown to a steel bar of 25 x 90-mm cross section. The strains at A and B have been 30 mm measured and found to be A 84 = +350 u 8z = -70 u 90 mm B 45 mm Knowing that E = 200 GPa, determine (a) the distance d, (b) the magnitude of the force P. 15 mm
The force in DB of the truss shown in below figure is W A C O VW tension 5m √3 W compression 2 W compression 5 W tension E D 2W 5m B
The moment M acting on the cross section of the tee beam is oriented at an angle of 0 = 53° as shown. Dimensions of the cross section are b= 160 mm, tf = 13 mm, d = 181 mm, and tw = 8 mm. The allowable bending stress is 210 MPa. What is the largest bending moment M that can be applied as shown to this cross section? bf M k B
2. Resolve the vector force into its components in the Figure shown. * Z 2m F=80 kN 5m 3m