2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m? (tensile) and 70 MN/m2 (Compressive). The shear stress across the planes is 65 MN/m². Find the following by Mohr's Circle method and compare with Analytical solutions: (i)The Normal stress on a plane making an angle of 50° with the plane of first stress. (ii)Shear stress on the plane (iii) Maximum shear stress- (iv) Resultant stress and it's direction. (v) Major and minor principal stresses.

2. At a point in a brocket, the stresses on two mutually perpendicular planes are 180 MN/m? (tensile) and 70 MN/m2 (Compressive). The shear stress across the planes is 65 MN/m². Find the following by Mohr's Circle method and compare with Analytical solutions: (i)The Normal stress on a plane making an angle of 50° with the plane of first stress. (ii)Shear stress on the plane (iii) Maximum shear stress- (iv) Resultant stress and it's direction. (v) Major and minor principal stresses.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
-18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,,sy., andtxy(see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
.4-2 An element in uniaxial stress is subjected to tensile stresses sx= 57 MPa. as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at an angle 0 = 33° from the x axis (minus means clockwise). (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
-4. - An element in plane stress is subjected to stresses ??x= 105 MPa, ??y= 75 MPa, and sxy= 25 MPa (see the figure for Problem 7.3-1). Determine the principal stresses and show them on a sketch of a properly oriented element.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.