2.18 Two strnctural members A and B are holted to a bracket as shown, Knowing that hoth members are in compression and that the force is 15 kN in member A and 10 kN in amember B, determine by trigonometry the magnitude and direction of the resultant of the forces applicd to the bracket by members A and B.

2.18 Two strnctural members A and B are holted to a bracket as shown, Knowing that hoth members are in compression and that the force is 15 kN in member A and 10 kN in amember B, determine by trigonometry the magnitude and direction of the resultant of the forces applicd to the bracket by members A and B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.17P: The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1...

See similar textbooks

Similar questions

The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1 and T2 is a vertical 3200-lb force, determine T1 and T2.
Determine the horizontal and vertical components of force that the pins at A and B exert on the frame. 4.1 The magnitude of the horizontal component Ax at the hinged support A is Blank 1 kN. 4.2 The magnitude of the vertical component Ay at the hinged support A is Blank 2 kN. 4.3 The magnitude of the horizontal component Bx at the hinged support B is Blank 3 kN. 4.4 The magnitude of the vertical component By at the hinged support B is Blank 4 kN.
2. A person's arm is used for ergonomic studies. If the distance of the AB, BC, and CD segments are 35.0 mm, 28.0 mm, and 19.0 mm, respectively, and the model is holding a small 1.5-lb load on the distal metacarpals of her hand . Determine the magnitude and direction of the moment of force with respect to a) to the shoulder joint, b) to the olecranon joint, c) to the carpal joint.
1.6.11 If the axial force in the tie rod DE is P = 1000 N, determine the two nonrectangular components of the force P, one having a line of action along AB and the other parallel to AC. See Fig. 1.6.4. 12 Fig. 1.6.4 B.
Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as shown, determine the magnitude F of the equal forces exerted on the four contact points on the 1-in. bolt head so that their external effect on the bolt is equivalent to that of the two 50-lb forces. Assume that the forces are perpendicular to the flats of the bolt head. 50 lb A View C Detail (clearances exaggerated) 14" 50 lb 14" B. Q4) A commercial airliner with four jet engines, each producing 90 kN of forward thrust, is in a steady, level cruise when engine number 3 suddenly fails. Determine and locate the resultant of the three remaining engine thrust vectors. Treat this as a two-dimensional problem. 4 90 kN 9 m 12 m 12 m 90 kN 9 m 90 kN 1 Good luck
3.6 m. For the frame and loading shown, determine the components of all forces acting on member ABE 2.7 m 2400 N 2.7 m 1.5 m 4.8 m
Determine the value of w and P such that the resultant of the system is a downward force of magnitude 1200 N acting 3.6 m to the right of A. Determine the magnitude of the uniform load w. a.252 N/m b.646.1 N/m c.387.7 N/m d.553.8 N/m
2. A 90 N force is applied at an angle of 30° from the horizontal to the handle of a stroller as shown. Determine the moments of the force about (a) the front wheel and (B) the back wheel. The distance between the wheels is 0.8 m. Write your answers using 2 significant digits. F 1.05 m 1.0 m
A force of 150 N is applied to point A of the lever.Knowing that the distance AB = 225 mm, calculate themoment of force relative to point B when alpha=50 degrees.
Two structural members A and B are bolted to a bracket as shown. Knowing that both members are in compression and that the force is 15 kN in member A and 10 kN in member B, determine by trigonometry the magnitude and direction of the resultant of the forces applied to the bracket by members A and B.
%VY li. o HW#6_Ch.4 (Part C... 4.9 4-154. Replace the distributed loading by an equivalent resultant force and specify where its line of action intersects a horizontal lin +Dmonoured from A. 4-155. Replace the distributed loading by an equivalent resultant force and specify where its line of action intersects a vertical line along member BC, measured from C. 3 kN/m 3 m 2 kN/m 4 m Probs. 4-154/155 *415
Q.2. Force P is acting in the negative y-direction and has a magnitude of 120 N, and force Q is acting in the negative z-direction and has a magnitude of 225 N. Given this loading, solve for the forces in members AB, BC, EC, ED and AD. A 0.6 m 3 m B 0.6 m 2.25 m 1.2 m 0.75 m