2000kg cast iron housing at 450 degree Celsius is quenched in 5000kg of water at 15 degree C. What is the amount of heat transferred to water, use specific heat of water to be 4.18 kJ/kg.K and specific heat of iron to be 0.42 kJ/kg.K

2000kg cast iron housing at 450 degree Celsius is quenched in 5000kg of water at 15 degree C. What is the amount of heat transferred to water, use specific heat of water to be 4.18 kJ/kg.K and specific heat of iron to be 0.42 kJ/kg.K

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.39P: The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must...

See similar textbooks

Related questions

Q: is often used for welding materials that can accept only a low heat input, e.g. certain stainless…

A: Laser beam welding is often used for welding materials that can accept only a low heat input. Laser…

Q: b) What was the CMB energy density at the time of decoupling at z = 1088 (according to a WMAP…

A: (b) Write the given data. z=1088 Calculate the energy density at the time of decoupling. E=1+z4E0…

Q: Aluminium with an unknown mass and an initial temperature of 28 °C is to be melted in an arc furnace…

A: As per the company guidelines we will answer the first question for you. Given data: Let m is the…

Q: A piece of titanium metal with a mass of 20.8 g is heated in boiling water to 99.5°C and then…

Q: Consider a material with a specific heat of 480 J/kg-K, a heat of fusion of 0.24×105 J/kg and a heat…

A: Given data: Heat of fusion (Qf) = 0.24*105 J/kg Heat of vaporization (Qv) = 9.4*105 J/kg Need to…

Q: Refer to Figure B. What is the value of member FG? What is the value of member GH? What is the…

Q: Give explanation how you obtained specific heat constant pressure. 10 kg / s of toluene enters an…

Q: A 110-volt electrical heater is used to warm 0.3 m3/s of water from 19oC to 98°C . Assume heat…

Q: What possible error can occur by using (a) a single large piece of ice or (b) very fine shavings of…

A: If there should arise an occurrence of bigger part of the ice it has more modest surface region than…

Q: A container holding 3.00 kg of water at 20.O°C is placed in a freezer that is kept at -20.O°C. The…

A: Please go through the solved solution below for total clearity and find your mistake.

Q: Determine the internal energy change for carbon monoxide, in kJ/kg, as it is heated from 312° K to…

A: Given:T1=312 KT2=1456 K

Q: At temperatures above 500K, the specific heat capacity of copper is represented by the equation…

A: Specific heat capcity equation; CP=a+b TLet ∆h is the enthalphy change for 1kg…

Q: A 110-volt electrical heater is used to warm 0.3 m3/s of water from 19°C to 98°C . Assume heat…

Q: 20,000 J of heat is supplied to a 5 kg mass. If the temperature rises from 20oC to 30o C, calculate…

Q: Define the specific heat capacity with equation? How much thermal energy is required to change a 40…

Q: Define the following terms: a. heat of fusion b. heat of vaporization c. heat capacity d. boiling…

A: note: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts…

Q: In an insulated, constant volume closed container, there is 3 kg of saturated liquid-vapor mixed…

A: m=3 kgP=.2 Mpax=.2 V=20 volt I=2 amp Q=P=VIQ=20×2=40 watt

Q: A substance has a melting point of 20°C and a boiling point is 150°C. The latent heat of fusion of…

A: According to the conservation of energy, The heat gain by the ice should be equal to the heat loose…

Q: * Assuming that the densities of water in all phases are 1 g/mL and that the Cp (J/K- mole) for ice…

Q: A 30.14 g stainless steel ball bearing at 117.82°C is placed in a constant-pressure calorimeter…

A: Given: Mass = 30.14 g Temperature = 117.82°C Specific heat = 0.474 J/g • °C Volume of H2O = 120.0…

Q: Derive energy equation from the first law of thermodynamic with detailed steps on how the…

A: Energy: The ability to do work is known as energy. The energy stored by an system in many forms such…

Q: 1-The solid phase in the Isomorphism Systems is a . . Solid, while in Iron - Carbon solid solubility…

A: As per the Bartleby Answering Guidelines we are suppose to answer first three subparts of questions.…

Q: How many BTU/min is required to produce 10 metric tons of ice per day at -10°C from raw water at…

Q: What mass of sweat(water) must evaporate from the skin of a 70.5 kg man to cool his body 0.85 "C?…

Q: (2a) -A cylinder contains a gas at 200°C, volume 5 liters and a pressure of 2.2MPa. The polytropic…

A: As per our guidelines, we can answer only the first question. Kindly post the remaining question in…

Q: (a) How much heat transfer is necessary to raise the temperature of a 0.200-g piece of ice from…

A: (a) Calculate the heat transfer hfg =2257 kJ/kg…

Q: A dead body was found within a closed room of a house where the temperature was a constant 66 °F. At…

Q: a) : What is a Heat treatment process and why it is important? (b) : Explain the Annealing and…

A: Answer a. Heat treatment is a combination of controlled heating and cooling operations. It is an…

Q: 02/ A metal with 1.5T, k cooled to 300 k by transferring heat to environment at T = 27" Describe the

A: givenInitial temperature of the T1=1.5TK=1.5×300=450KEnvironment temperature T=300Kweight of metal…

Q: Water has a latent heat of fusion of -334 MJm, surface free energy of 0.195 Jim, and meting point of…

Q: The energy densities of various types of coal are listed below: Anthracite 35kJ/g…

A: Write the given data: Ccal=1.3 kJ/°C∆T=8.75 °Cm=0.367 g

Q: Calculate how much energy (J) is required to heat up a pot containing 500. g of water from 23.0 °C…

A: Given Mass, m =500. g = 0.5 kg Temperatures, T1 and T2 = 23.0 °C…

Q: QI/ Explain with drawing the Time- Temperature- Transformation (TTT) diagram?

A: TTT Diagram :- Note :- you have posted multiple questions on single window. As per the…

Q: 29. An ideal mono-atomie gas is confined in a cylinder with°the help of a piston that can slide…

A: Monoatomic gas, degree of freedom, x = 3 γ =1+ 2x = 1+ 23 = 53 , the ratio of specific heat State 1:…

Q: A 43.9 g spoon made of pure silver (cs = 0.235 J/g C) at 20.1 C is used to stir an 8 oz. (240 g) cup…

A: The mass of the silver spoon is m1=43.9 g. The specific heat of silver is cs=0.235 J/g°C. The…

Q: (c) A hardboard wall is exposed to a window on a neighbouring property which is 2 metres high x 2…

A: Laminar flow :Fluid flow in which the adjacent layer of the fluid do not mix with each other and…

Q: 4 A closed vessel of 1.2 m3 in capacity contains steam at 3 bar and 0.85 dryness fraction. Steam at…

Q: A steel flask of 0.04 m capacity is used to store Nitrogen at 120 bar and 20°C. The flask is…

Q: A 2 kg of coal sample was burnt in a bomb calorimeter. The heat liberated was estimated and found…

A: A bomb calorimeter is a device that is used to measure the heats of combustion. The reaction takes…

Q: By referring to the thermodynamics tables, calculate the missing properties in the following table…

A: Given: Substance: H20, NH3, R-134a and their properties. To find: To find the missing properties and…

Q: (a) An incoming stream of 1500kmol/min consists of saturated water with 65% liquid water and 35%…

Q: A substance has a melting point of 20°C and a heat of fusion of 2.4 × 10 to power of ((4)) J/kg. The…

Q: A steel flask of 0.04 m³ capacity is used to store Nitrogen at 120 bar and 20°C. The flask is…

Q: Explain in detail what affects human comfort?

A: TO explain: what affects human comfort

Q: The machine is commenced to be heated at some point of a quasi-equilibrium manner till the…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Read the question carefully and give me all right solutions. Note: No need the diagram 100 kg of water is heated from 10°C to 100 o C in a square container that is 0.5 meters wide by 0.5 meters long, by 5 meters high. There is not top on the container, e.g. it is open to the atmosphere. What is the change in volume of the water due to the temperature change assuming all other things being equal and no liquid is lost to vaporization? What is the rise in the water surface (Ah) in the container due to the increase in temperature? What is the specific gravity of the water at relative to water at 20°F?
4. When 435 J of heat is added to 3.4 g of olive oil at 21 C, the temperature increases to 85 C. What is the specific Heat of the olive oil?
(English Unit) A 100-pound meat is moved to the cold storage room. During preparation for storage, the meat may warm up to 45°F. That means the meat must be cooled to 32°F before it will begin to freeze. The average latent heat of fusion amounts to about 90 Btu/lb for meat. After freezing, the meat is subcooled to the quick-freeze temperature of 14 oF. The meat has a specific heat below and above freezing point of 0.7 and 0.4 Btu/ lb-oR, respectively. Find the total heat removed from cooling BTU.
What is the final temperature when a 200-gram copper with specific heat of 0.1 cal/gm-°C is at a temperature of 80°C when it is added to a 200 gram of water at 20°C that is held in a 50-gram aluminum cup having a specific heat of 0.22 cal/gm-°C. COMPLETE FBD SOLUTION AND REQUIREMENTS PS. THIS IS A HEAT TRANSFER PROBLEM
Determine the amount of heat removed from 1.5 kg of bologna (sausage)when cooled from 24C to -7C. Assume MC of 59% and at -7C, 22% won’t be frozen.
A sample of water that is initially at 84.00C absorbs 500 kcal of heat. As a result, the liquid water becomes water vapor at 1150C. What is the mass of the water? (Some useful information: cwater = 1 cal/g0C, Lv,water = 540 cal/g, and csteam = 0.480 cal/g0 C. a. 488 g b. 788 g c. 588 g d. 888 g e. 688 g
• 100 Ibs of glycerin at 200 oF with a specific heat of 0.58 loses 10000 btu of heat. What is the final temperature of the glycerin?
The Heat Capacity of an Ideal Gas at T=50 oC is equal to c= 79.314 kj (kmol. k) . What is the value of dS/ dlnT )v
Calculate heat capacity of a metal if the specific heat and the molar mass of that metal are 40 J/kg-K and 27 g/mole respectively. Select one: O a. 1080 J/mole-K O b. 1.48 J/mole-K O c. 0.68 J/mole-K O d. 1.08 J/mole-K
Define the specific heat capacity with equation? How much thermal energy is required to change a 40 g ice cube from a solid at -10 oC to steam at 110 oC?
Please answer heat transfer
A Metal container with a mass of 2 kg and containing 2.30 kg of water is put it on a fire. Assume that there is no heat exchange with the surrounding, how much heat must be added to raise the temperature from 20.0 o C to 80.0 o C. (CAl= 910 j/kg•K and Cwater=4190 j/kg•K)