20μF R1 R2 Vc 0.5mH R3 0.4mH 12V 10µF 25V Assume the above circuit has been in this state for a very long time. Determine the voltage across the 20UF capacitor vr given R1=30 R2 =50 R3 = 40 Note: Round your answer to the nearest single digit decimal place. Your answer should be in Volts. For example, if you compute 15.43 Volts then enter 15.4 as you answer. Find Vc

20μF R1 R2 Vc 0.5mH R3 0.4mH 12V 10µF 25V Assume the above circuit has been in this state for a very long time. Determine the voltage across the 20UF capacitor vr given R1=30 R2 =50 R3 = 40 Note: Round your answer to the nearest single digit decimal place. Your answer should be in Volts. For example, if you compute 15.43 Volts then enter 15.4 as you answer. Find Vc

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
d) Design (Find the values of the R₁, R2, and C₁) an astable multivibrator circuit to have an output waveform as shown below in the figure (tH = 375µs and t₁ = 125µs). (Assume C₁ = C₂ and R₁ # R₂) and determine the frequency of oscillation and the duty cycle. R1: R2 C1 Q Vcc 4 555 5 C2 10nF I 8 1 3L -OVO tH = 375.0us tL = 125.0us
this is electric circuit questin ...plz solve it early .plz solve early
Why this happening to my circuit? I am inputting a 0-3.3 V sine wave into my voltage follower circuit using NE5532P. At the output I am seeing 0-3.3 V sine wave as expected. However, when I add a 1000 uF capacitor and a loudspeaker to listen to the sine wave my wave is clipped and its reading -800 mV for min and +680 mV for max on the oscilloscope. How do I fix this so that I only listen to 0-3.3 V sine wave? I'm in the lab and this is confusing to me.
Sketch out the fellowing signals: (a=7, b=5, c=8) a-) V = 15a(sin2r1000*ct) b-) V = 3b(cos(7500*ct)+3) c-) Assume that you measure the signal V1 using Digital Volt Meter(DVM) and ossiloscope. What will you read on the DVM display and oscilloscop dispaly when the input voltages are defined as 1-) V = 15a(sin2m1000*ct) 2-) V = 3b(cos(7500*ct)+3) Write down and sketch all the voltages for each case. Show all parameters, including period and maximum values of the signals. aR V AC aR V, aR What will you read at the DVM display when you read the voltages at AC mode What will you read at the DVM display when you read the voltages at DC range
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
Electrical Engineering In what connections the third harmonic is not exist?
An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin. Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohms
Can you explain how will integrate in this problem step by step
R +Vcc -Vcc C Vout R R a. Quantify how the resistors and the capacitor influence the output voltage of the circuit, Vout. What are the upper and lower limits of Vc? b. Howlong does it take for the capacitor to be charged from minimum to maximum voltage and vice versa?
Signal subject 2