25kn 25kn Wr 25kn 25kn 20kn 4kO 10kO 6kQ 25V (* + 3kQ + 1. Compute for the equivalent resistance (in ohms) of the boxed portion of the circuit. 2. TRUE OR FALSE. When mesh analysis is used, there will be one less unknown current variable. 3. Suppose we simplified the boxed area into a single resistance. Using this circuit, which will result in fewer unknowns? Nodal, Mesh or Both will result in the same #of unknowns? 25kn

25kn 25kn Wr 25kn 25kn 20kn 4kO 10kO 6kQ 25V (* + 3kQ + 1. Compute for the equivalent resistance (in ohms) of the boxed portion of the circuit. 2. TRUE OR FALSE. When mesh analysis is used, there will be one less unknown current variable. 3. Suppose we simplified the boxed area into a single resistance. Using this circuit, which will result in fewer unknowns? Nodal, Mesh or Both will result in the same #of unknowns? 25kn

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

1. Using Series-Parallel concept, Find the following for the given circuit. The value of the power supply and resistances are given in Page-4. a) the current supplied by the source b) the voltage drops across each resistor c) the r dissipated by R3 R1=45kn R2=2kn R3=22kQ R4=14kn R5=17kn R6=85kn V1=24 v R₁ R₂ V₁ R₂ R₂ R₂
True/False: Consider connecting a Load Resistance across R2. Loading Effect is less when voltage across R2 'with load' is close to the Voltage 'without load' * Vin R2 V. out True O False
3. In your estimation would Vr = IR₁ = IR₂ = IR3 resistive branches? Explain. = ... be true for all parallel 4. In a parallel circuit, the amount of current in each separate branch depends upon which factor? 5. Could you always expect that R7 = R₁ + R₂ + R3 + circuit? Explain. in a series resistive
With the values of the mesh currents (I1=-0.004A, I2=-0.040258A, I3=0.13345), calculate the branch currents and voltages in R1,R2,R3,R4,R5.
Part B - Find the short-circuit current The circuit you should use to find the short-circuit current, isc, is shown here. Note that the resistor to the right of terminals a and b has been replaced by a short circuit, and you must find the current in that short circuit. Use any circuit analysis technique you like. isc=
The Thevenin's equivalent circuit is a method used to convert the complex circuit into simple equivalent circuit with; (A A voltage source in series with a resistance. B A voltage source in parallel with a resistance. A current source in parallel with a resistance. D A current source in series with a resistance.
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
Write the system of nodal equations via nodal analysis for this circuit. Make it very detailed explaining the steps and also how nodal analysis should generally be performed in circuits such as this one. And how do we know how many kcl equations we should do ( it's general formula) thank you
R₁ =1292 Igc = 0.16A IDC = Problem #21) Determine the source current Ipc and the resistor voltage V4 as shown in the following circuit using the Reduce and Return Method if the source voltage is Vpc = 72 volts. R₂=402 R₁ =1552 R₁=4592 0.16 IDC =. V₁=. 2 (A) 36 (A) (V)
3) For the resistor networks below, find the equivalent resistance between A - B for circuits a. and b. For circuit c. you should compute the equivalent resistance as seen from A - B and C-D. The answers will be different. When viewing the circuit from A-B, the terminals C-D will be open circuit. Likewise, when viewing from C- D, the terminals A-B will be open circuit. Think about what this means in terms of where current can flow. Only circuit elements which are in the current flow contribute to the equivalent resistance. In more formal terms the resistor must be part of a 'loop'. Be sure to draw successively simplified equivalent circuits to illustrate your solution process. a. b. C. 10 Q A B ww 500 £ ED 4kQ 3 kQ www 200 R1 25 > 200 R3 40 2 KQ ΚΩ 18 Q R2 20 R4 120 40 Q All Resistors are in Ohms 1.5 ΚΩ ww 70 R5 40 C D 1.5 KQ
After transforming R2, R3, and R5 from wye connection to delta connection, what are the values of the resistances (in ohms) of the resulting delta connection? List them in any order below.
Consider the circuit in the figure. Use the included current directions (arrows) and component labels. a) Which of the following equations would be the correct equation for the junction labeled c? - I1=I2+I5 - I2=I1+I3 - I1=I2+I3 - I1=I2+I4 B) Which of the following equations would be the correct equation for the junction labeled d? - I3=I4+I5 - I3+I4=I6 - I3+I4=I5 - I3+I5=I4 C)Which equation for the junction labeled g? - I6+I5=I4 - I6+I4=I5 - I6+I4=I6 - I6=I4+I5 D) Now you have the junction specifying each current. What is the accurate representation of the loop a=>b=>c=>h=>a? E) What is the accurate representation of the loop equation a=>b=>c=>d=>g=>h=>a? F)What is the accurate representation of the loop equation for loop d=>e=>=>g=>d? (Make sure you follow the directions of the currents drawn)