(3) 12" 4 #9 1² + 21" "3" fé= 4ksi. Nwc Grade 60 steel, Tied Bars. Mn=?

Q: *Determine (a) the principal stresses, (b) maximum shear stress, and (c) the orientations of the…

A:

Q: Given the following Mass-Haul Diagram: O $30,000 O $28,000 O $25,375 O $20,250 Net Cumulative…

A: Given:- The mass-haul diagram is given: The limit of free haul = 600 ft The price of excavation =…

Q: A 3.5m long column (W18x55) at the ground floor is pinned at the bottom and fixed against rotation…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 4. For the vessel containing glycerin under pressure, calculate the total pressure at the bottom of…

A: Given Data Air pressure (Pa) = 50 kpa = 50 × 103 N/m2  Determine the total pressure at bottom of…

Q: A simply supported beam carries situated at the right support Determine the following: ● ● ● a…

A:

Q: Calculate a) the position of the centroid b) the moment Ic, with respect to an axis passing through…

A:

Q: During plate load test, the settlement of a 35 cm plate is found to be 2 cm in a cohesive soil, then…

A: Given- Plate settlement Sp=2 cm Width of plate Bp=35 cm Footing width Bf =85 cm Footing settlement…

Q: Question 14 How many reaction force(s) does a roller support have? 00 01 03

A:

Q: The 5-Mg truck and 2-Mg car are traveling with the free-rolling velocities of 37 km/h and 13 km/h,…

A:

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E = 29 000 ksi). If the end C is…

A: Given,        A-36 guy wire BD having elasticity,E = 29000 ksi. End C displace downward by 0.75…

Q: 3. The school building has interior columns that are spaced 6 m apart in two perpendicular…

A: Answer  We know that reduced live load is given by L = Lo0.25+4.57KLLAT             In SI units L =…

Q: 1. A wastewater is treated in an aerobic CSTR with no cell recycle. The following hold: Ks= 50mg/l;…

A:

Q: 1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: A stress element is given with stresses shown. Young's modulus of elasticity, E = 80GPa Possion's…

Q: 1. The open rail car is 7 ft wide and filled with water to the level shown. If the car moves with a…

A: Given, Width (b) = 7ft  Acceleration (a) = 10 ft/s2

Q: (ii) Consider a primary sedimentation tank (PST) in a water treatment plant with surface overflow…

A:

Q: Seatwork 1. A car drifts from a slope of 42° at a height of 1.7m. It was observed that it stayed in…

A:

Q: 3. The school building has interior columns that are spaced 6 m apart in two perpendicular…

A: Given:- The school building has interior columns The spacing between the columns = 6 m  To…

Q: for both (a) and (b), the stresses in the ropes and find the downward movement of pulley and the…

A:

Q: Vehicles begin arriving at Allen fieldhouse at 6:30 PM, at a constant rate of 4 per minute. One gate…

A:

Q: A B 400 mm 500 mm 20 mm 40 mm 7 kN/m 3 m 20 kNm 2.5 m 2.5 m 2 m 15 KN A T-beam with the…

A: Given Data Determine  a. Second moment of area of cross section.  b. Draw the SFD and BMD.  c.…

Q: The Write up is an opportunity to briefly answer the ASLA DISCOVER LANDSCAPE ARCHITECTURE BOOK FOR…

A: The ASLA Discover Landscape Architecture book for kids is a fun and educational resource that…

Q: Given a q of 25 ft²/s and a sluice gate/jump configuration. What depth upstream of the sluice gate…

A: Given  q=25ft2/s Critical depth yc3=y1y2y1+y22whereyc=critical depthy1=depth at upstreamy2=depth at…

Q: A reinforced concrete cantilever beam has a span of 5m. It supports a factored load of 60kN/m…

A:

Q: Prob. 4 The figure below gives a cross section of a concrete dam. The subsoil is anisotropic and has…

A:

Q: Problem 1: Determine the flexural strength of a W 410 x 67 beam with a simple span of 8 m and Fy =…

A:

Q: calculate daily dose of benzo(a)pyrene of adult via ingestion, whereC = Contaminant concentration…

A: Answer We are given Where C = Contaminant concentration = 1.5 mg/kg IR = Intake rate = 20 kg/day RAF…

Q: 1. At a depth of 10 ft the recorded SPT blows per six inches were 7-15-17 for a sandy soil. The…

A: Data given Depth = 10 ft SPT blows per 6 inch = 7-15-17 Equipment - Mobile B-53 rig unit weight of…

Q: Consider a laminar flow over a flat plate of length L= 1 m. The boundary layer thickness at the end…

A: Given data,  L = 1 m Vw = Va Kinematic viscosity of water = 10^-6 m²/s Kinematic viscosity of air =…

Q: Water (p = 1000 kg/m³) flows horizontally through a nozzle into the atmosphere under the conditions…

A: Given data- Density of water- ρ=1000 kg/m3At section-1A1=10-3 m2V1=2 m/sP1=3×105 Pa(gauge)At…

Q: Final measurement of 5 meters if we use the scale 1:100 and 1:50

A: Length L = 5m Scale: 1:100 1:50

Q: A cylindrical tank (Figure 2) of diameter 50cm connected to a horizontal pipe (diameter is 8 cm)…

A: Given Data  Inlet velocity (Vi) = 5m/s = 500 cm/s  Outlet velocity (Vo) = 3.5m/s = 350 cm/s…

Q: The thin walled tube is used as a beam to support the uniformly distributed load of intensity w, as…

A:

Q: Explain the relationships in the excel graph

A: The given plots are to be explained.

Q: 4. For the vessel containing glycerin under pressure, calculate the total pressure at the bottom of…

A: Given: Air pressure (Pa) = 50 kpa = 50 × 103 N/m2  Determine the total pressure at bottom of tank…

Q: Determine the tension in each section of the cable, the horizontal load at point C and the length…

A:

Q: A vertical retaining wall 6 m high is supporting a horizontal backfill having a weight of 16.5 kN/m3…

A: The given data is shown below:

Q: The direct and indirect costs estimated by a contractor for bidding a project is 160000 and #20000…

A: Given data: Direct cost DC = Rs 160000, Indirect cost IC = Rs 20000, Markup =10 % of the bid price.

Q: The cross-section of a short-reinforced beam is shown in Figure 1. Calculate: 2.1 The stress in the…

A: Axial load = 500 kN = 500000 N E steel (Es) = 210 GPaE concrete (Ec) = 14 GPa Length of Column = 1.5…

Q: Calculate the internal force in each bar for the roof truss as shown below. For each bar, indicate…

A:

Q: IV: Structural steel buildings frequently are designed with diagonal bracing systems to resist…

A:

Q: In a catchment area, approximated by a circle of diameter 100 km, four rainfall stations are…

A:

Q: What are the sources of Ignition? Explain each.

A: Ignition is the process of initiating combustion or a fire. It occurs when a source of heat, flame,…

Q: 23. The gasoline tank of a car contains 50 liters of gasoline and alcohol, with alcohol comprising…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

A:

Q: PROBLEM 3 Determine the centroidal moment of inertia, Ixx of the cross section shown. 6 in H .5 in…

A: Built up section is given and it has been asked to determine moment of inertia about x axis. Please…

Q: From the given figure below. Using Ranking Theory, the unit weight of concrete of gravity dam is 24…

A: Given:- The unit weight of the concrete = 24 kN/m3  The coefficient of friction between the concrete…

Q: For an unconfined aquifer, the specific yield is 20%, specific retention is 15%, and permeability is…

A: Given data- An unconfined aquifer- Specific yield Sy= 20%, specific retention SR = 15%,…

Q: 1. What is the value of Vu at a distance "d" from the face of the support? 2. What is the value of…

A:

Q: 2. Determine the force in each member of the space truss shown in the figure. The truss is supported…

A: Given:- The truss is supported by a ball-and-socket joint at A A slotted roller joint at B and a…

Q: 4. For the vessel containing glycerin under pressure, calculate the total pressure at the bottom of…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.