3) The contaminant concentration has been detected to be 200 mg/L for the area of a site represented below. The groundwater contours are spaced at intervals of about 50 m. The average thickness of the aquifer is 5 m and the hydraulic conductivity is 1x10-2 cm/s. For each meter of length (unit length) as measured parallel to the river, what is the contaminant loading rate (i.e., Cx Q) in kg/year?

3) The contaminant concentration has been detected to be 200 mg/L for the area of a site represented below. The groundwater contours are spaced at intervals of about 50 m. The average thickness of the aquifer is 5 m and the hydraulic conductivity is 1x10-2 cm/s. For each meter of length (unit length) as measured parallel to the river, what is the contaminant loading rate (i.e., Cx Q) in kg/year?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A. Given the level section data below. D 23.7 23.1 7.8 5.3 C 12 Station CL 1+200 C 7.8 C 5.3 C 7.4 23.7 0 23.1 1+250 C 6.5 C 6.0 C 7.5 21.75 0 23.25 1+300 C 8.5 C 6.6 C 7.0 24.75 0 22.5 Roadbed =24m Side slope 1.5 : 1 R= 700m, center of curvature is on the right. Compute for the: 1) Volume by end area method = 2) Volume by prismoidal method= 3) Prismoidal correction = 4) corrected volume by applying this prismoidal correction = 5) curvature correction = 6) corrected volume for the following cross-section= 12 7.4
Q4/ The elevation of center line for a cross section of street project. If the design level for the proposed street is (25m). Examine if the section is Fill or Cut? (4₂² 4.0 6.0 परा 6.0 2-0 8.0 2.0 0.0 Pcm) 810 E. 25.60 26.20 25,8 26.60 25.50 27.60 26.90 26.0 255
Q2). Calculate volume of cut and fill, the elevation of natural ground shown on all nodes and design elevation is equal to 103 m, all dimension and elevations are in meter. hi h, 101 102.5 W₂ 104.2 ha 108.10 98.45 412 100.5 Wy -10 m 102.5 hey 105.7 12 97.35 99.80 101, hs 104 hi 10 m ha 104 106.5 hi Thi
A steel column has a cross-sectional area of 0.126 m^2 and a length of 3 m. If a 50000 KN load is applied to the column, determine the normal stress in the column. A steel has a modulus of elasticity of 200 GPa. *
BALANCE THE TRAVERSE BY TRANSIT RULE AND COMPUTE THE AREA BY DMD METHOD Corr'n Corr'n Distance Line Bearing Latitude Departure Corrected Latitude DMD Corrected Departure Lat Dep Double deg min 1 2 s 23 37E 113.35 2 3 s 25 56 w 93.32 3 4 s 87 25 w 172.92 4 5 N 55 46 w 165.88 5 6 N 51 59E 184.89 6 1 s 85 51E 160 S() E (+) S(-) N(*) W(-) N (*) E (+) W() Area
ineed solutions ANSWER Vs = 120453.0446 N
alculate volume of cut and fill, the elevation of natural ground shows on all nodes and elevation is equal to 102.5m, all dimension and elevations are in meter. 101 (2) 102.5 C 104.2 C 108.10 f 98.45 -10 m- f 100.5 (4) 102.5 C 105.7 f 97,35 f 99.80 101, 104 10 m C 104 106.5
pls answer 1.62
Using the given data in the traverse shown: POINTS A BCDEF с E NORTHINGS 75 m. 425 m. 675 m. 675 m. 425 m. 175 m. Find the Area of the lot using a. DMD Method b. DPD Method EASTINGS 250 m. 150 m. 450 m. 675 m. 700 m. 550 m. Note: Using both methods will give same answer
Choices for member BC 6,105.37kN(T) 6,105.37kN(C) 6,005.37kN(T) 6,005.37kN(C) Member BD choices 10,501.61kN(T) 10,501.61kN(C) 10,401.61kN(T) 10,401.61kN(C) Member AB choices 13,010.74kN(C) 13,010.74kN(T) 12,010.74kN(C) 12,010.74kN(T)
1. Calculate the grade of points A, B and C. El. 126.42m 3.70% 158.75 A -4.1% 66.45 126-866- B 2.90% 205.6 C
Q.3 A level circuit is shown in figure. The survey, needed for local engineering project, commenced at BM 35, the elevation of new benchmarks 36, 37, 38 and 39 were determined, and then the level survey was looped back to BM 35, the point of commencement. Fined the adjusted new BMs. ВМ 35 Elevation(m) 190.000(fixed) 35 36 37 38 39 35 188.242 186.299 188.251 186.397 190.033 IM 36 09 km DM 35 0.8 km OBM 37 08 km O6 km DM 39 BM 30 0.7 km