3. Complete a table simildr to N for the first trial; a mass of 200 g is added in the next trial. Consider the following results: Trial 1- applied force for constant velocity is 1.58 N, coefficient of static friction is 0.57; Trial 2- applied force to move object is 4.16 N and 1.97 N to move it at constant velocity. [Use two (2) decimal places). in Experiment No.3. Lef weight of block equal TO 5.60

3. Complete a table simildr to N for the first trial; a mass of 200 g is added in the next trial. Consider the following results: Trial 1- applied force for constant velocity is 1.58 N, coefficient of static friction is 0.57; Trial 2- applied force to move object is 4.16 N and 1.97 N to move it at constant velocity. [Use two (2) decimal places). in Experiment No.3. Lef weight of block equal TO 5.60

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

100 cm 50 kN 25 90 The piston, crank and connecting rod for a reciprocating engine. The force on the piston is 50 kN and the coefficient of sliding friction between piston and cylinder surfaces is 0.1. Calculate: i. the force Q in the connecting rod ii. the friction force resisting motion of the piston. The weight of the piston may be neglected.
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m, attached to a 50-kg block in an incline (0=30°). With the spring initially at equilibrium position, the block was pushed 0.5 meters up the incline by a 30-N external force applied parallel to the path. The coefficient of kinetic friction is 0.30. d) How much work is done by the block (in Joules) on the spring? e) How much work is done by the applied push on the block? f) How much work is done by friction? HAM 10
... Try these Take g = 9.8 ms? 2 kg la A parcel of mass 2 kg lies at rest on a rough horizontal surface, as shown. i Draw a force diagram showing the forces acting on the parcel. ii Calculate the normal contact force, R. b The parcel is now pushed with a horizontal force P, as shown, so that it is just on the point of sliding. i Draw a force diagram showing the forces now acting on the parcel. ii If the coefficient of friction is 0.5, find the value of P when the parcel is on the point of sliding. 40 N 2 A dustbin of mass 12 kg standing on horizontal ground is pushed by a horizontal force of 40 N. 12 kg If the coefficient of friction is 0.4, will the dustbin move?
A 100 lb force acts as shown on a 300 lb block placed on an inclined plane as shown in Figure 4. The coefficients of friction between the block and plane are m, = 0.25 %3D and mk = 0.20. 00 Tb 100 lb 5 4 Figure 4 Answer the following questions. a) Determine whether the block is in equilibrium. b) Find the value of the friction force.
The nuchal ligament in a horse supports the weight of the horse’s head. This ligament is much more elastic than a typical ligament, stretching from 15% to 45% longer than its resting length as a horse’s head moves up and down while it runs. This stretch of the ligament stores energy, making locomotion more efficient. Measurements on a segment of ligament show a linear stress-versusstrain relationship until the stress approaches 0.80. Smoothed data for the stretch are shown. The volume of the ligament stays the same as it stretches, so the cross-section area decreases as the length increases. Given this, how would a force F versus change in length ΔL curve appear?
%£9 lI. O O A:". Test 3.pdf > F1 F2 a C F3 A B d. a F4 D E B Consider the following values: - F5 a = 12 m; b = 10 m; e = 10 m; d = 8 m; F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN; a = 30°, 0 = 45° , B = 60° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 111.6 kN.m b) 112.6 kN.m c) - 184.6 kN.m d) - 109.6 kN.m e) - 104.1 kN.m f) None of them 2] What is the resultant moment of the five forces acting on the rod about point B? a) -95.8 kN.m b) 42.7 kN.m c) 80.9 kN.m d) 10.9 kN.m e) 51.8 kN.m f) None of them 3] What is the resultant moment of the five forces acting on the rod about point C? a) 32.6 kN.m b) - 21.1 kN.m c) 17.4 kN.m d) - 16.5 kN.m e) 15.6 kN.m f) None of them 4] What is the resultant moment of the five forces acting on the rod about point D? a) 37.6 kN.m b) 73.8 kN.m c) 71.6 kN.m d) 52.1 kN.m e) 21.1 kN.m f) None of them 5] What is the moment of the force F2 about point E? a) 90.7 kN.m b) - 88.1 kN.m e) 54.6 kN.m d) 103.1…
A family wishes to buy a 2020 Toyota Camry. The two options the consider are (a) a standard automobile with and SI engine that gets 34 mpg and costs $18,000; and (b) a hybrid automobile that gets 52 mpg and costs $32,000. On average, the family drives 16,000 miles each year ad gasoline costs $1.65 per gallon. Calculate: (Show your complete solution) The amount of gasoline each vehicle would use each year. Gasoline cost savings of hybrid over standard. Time in months it would take to make up the difference in vehicle cost with fuel savings.
A homogenous ladder 10m long and weighing 35 kg leans against a vertical wall. The angle between it and the floor is 60 degrees. The coefficient of friction of the ladder against the ground as well as the wall is 0.25.1. How far up the ladder measured from the ground can a 70-kg man climb before it starts to slide? a. 5.506 mb. 6.671 mc. 4.493 md. 3.806 m2. Compute the reaction at the wall when it starts to slide. a. 17.59 kgb. 25.27 kgc. 29.66 kgd. 28.67 kg3. Compute the reaction between the ground and the ladder when it starts to slide. a. 88.82 kgb. 126.72 kgc. 112.7 kgd. 101.88 kg
You measure the elongation of springs placed on a graduated inclined plane, to which you attach masses. One end of the spring is attached to a hook at the top of the inclined plane and the other end is attached to a mass.The spring is parallel to the plane, and the force it exerts on the mass is also parallel to the plane.The angle of inclination of the plane is known, as well as its uncertainty.There is no friction between the plane and the mass.The natural length of the spring and its uncertainty are known.By hooking a known mass (m ± delta m), you measure that the spring now has a length (L ± delta L).We use the value g=(9.81 ± 0.01)m/s^2 for our calculations. Build a model to find the spring constant of the spring (with its uncertainty) given the known parameters. Then test your model with the following values: Plane tilt angle: (11.4 ± 0.2) degrees Natural spring length: (0.145 ± 0.001) m Attached mass: (0.15 ± 0.001) kg Spring length with a mass attached: (0.17 ± 0.002) m
Q2:An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centers 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted . [Ans. 2.387 kW]
1. Pressures up to 3000 bar are measured with a dead-weight gauge. The piston diameter is 4 mm. What is the approximate mass in kg of the weights required? 2. A gas is confined in a 0.47 m diameter cylinder by a piston, on which rests a weight. The mass of the piston and weight together is 150 kg. The local acceleration of gravity is 9.813 m's-2, and atmospheric pressure is 101.57 kPa. (a) What is the force in newtons exerted on the gas by the atmosphere, the piston, and the weight, assuming no friction between the piston and cylinder? (b) What is the pressure of the gas in kPa? (c) If the gas in the cylinder is heated, it expands, pushing the piston and weight upward. If the piston and weight are raised 0.83 m, what is the work done by the gas in kJ? What is the change in potential energy of the piston and weight? 3. Steam at 1400 kPa and 350°C [state 1] enters a turbine through a pipe that is 8 cm in diameter, at a mass flow rate of 0.1 kg: s-1. The exhaust from the turbine is…
A group of athletes were tested for isometric endurance by measuring the length of time they could resist a load pulling on their legs while seated. The approximate amount of time (called the holding time) that they could resist the load was given by the formula t = 31,293w^-1.5, where w is the weight of the load in pounds and the holding time t is measured in seconds. a. Determine the holding time for a load of 29 lb. b. When the weight of the load is tripled, by what factor is the holding time changed?