3. For the beams shown below construct the shear-force and bending-moment diagrams. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight- line and curved portions of the diagrams. 28 kips 9 kips/ft | 15 kN 18 kN |B 40 kN/m 3 ft 10 ft

3. For the beams shown below construct the shear-force and bending-moment diagrams. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight- line and curved portions of the diagrams. 28 kips 9 kips/ft | 15 kN 18 kN |B 40 kN/m 3 ft 10 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1: The cantilever beam below is subjected to external distributed loadings and forces between the endpoints and it is in equilibrium. The left hand endpoint A is hanging free and the right hand endpoint B is built in. You may assume that no external couple moments are acting on the overhanging part of the beam. The figure is not to scale. 4 m 0.5 m | (a) The shear force diagram of the beam is shown below; V (x) = -3(x – 2.5)2 + 3 for 2.5 < a < 3.5. Draw the complete free-body diagram of the beam, showing all the external forces, distributed loadings, and support reactions. V (kN) I (m) 1.5 2.5 3.5 -1 (b) Draw the bending moment diagram of the beam. Note that the area between V and the a-axis on the interval [2.5, 3.5] is 2. (c) Draw the free-body diagram of the part of the beam between a = 3.5 and a = 4, i.e. the part CB.
2. For the beam loaded as shown, (a) draw completely the shear and moment diagrams conventionally (b) locate the point of maximum deflection and (c) compute the deflection at 2.10 m from the extreme left. The modulus of elasticity is 200,000 MPa while the centroidal moment of inertia is 709 (106) mm¹. 73 KN/m 0.9 m 1.2 m 9 KN 30.02 KN m 1.8 m 9 KN 17.50 KN/m 1.2 m 7.3 KN/m 0.9 m
An extruded beam has the cross-section shown in the figure. A vertical shear force, V of 110 kN is acting at the shear center of the section. Uniform thickness is 9mm. 72 50 192 50 Use I = 22.055484 × 10° mm' Estimate the total vertical shear (kN) resisted by the web CD. A 117 B 110 C 103 D 96 The distance from the axis of the web to the shear center is most nearly equal to. A 35 mm B 20 mm 15 mm D 40 mm
THE OVERHANGING BEAM IN THE FIGURE CARRIES A TRIANGULAR LOADING, THE INTENSITY OF WHICH VARIES FROM O TO 10 KN/M, AN UNKNOWN CONCENTRATED LOADING P, AND AN UNKNOWN UNIFORMLY DISTRIBUTED LOADING W. KNOWING THAT IT HAS BEEN EXPERIMENTALLY DETERMINED THAT THE BENDING MOMENT IS +128/9 KN-M AT C AND +172/9 KN-M AT D. (A) DETERMINE THE VALUES OF P (IN KN) ANDW (IN KN/M), (B) DRAW THE SHEAR AND BENDING-MOMENT DIAGRAMS. (c) DETERMINE THE LOCATION OF ZERO SHEAR FROM POINT A AND THE MAGNITUDE OF MAXIMUM MOMENT. NEGLECT THE WEIGHT OF THE BEAM. HINT: THE LOCATION OF ZERO SHEAR IS ALSO WHERE M-MAX OCCURS. P 10 kN/m W C E A 2 m 2 m 2 m 2 m
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm Given: a- 4m b- 24kN/m c- 9kN
Q.1) (a) Calculate the support reactions of the loaded beam shown below. (b) Write shear-force and bending moment equations of the beam as a function of distant 'x' from the left-end of the beam for a beam section under the triangular distributed loading. (c) Sketch the shear-force and bending moment diagrams for the beam using the Graphical method. Label the values of shear-force and bending- moment at all key points. 200 N 300 N-m 50N/m 600 N-m 100 Nhm Q 2m
In the simply supported beam loaded and supported as shown, draw completely the shear and bending moment using shear and moment equations Problem 1. R₁ 300N/m 10m 5m 600N 5m R₂
Determine the slope and deflection at point B of the steel beam shown below using conjugate beam method. The reactions have been computed. E= 29(10³) ksi, I-800 in. 5k A (1 75 k-ft -15 ft- 5 k real beam -15 ft- B
How will the shear and moment diagram of the given beam look like? * W RA RB
PROBLEMThe beam shown below has internal hinges at points B and D. Assume EI is constant. Using your most convenient methodshow the following:a. Magnitude and directions of the support reactions (Ax,Ay, MA, Cy, Fy). b. The elastic curve.c. Vertical displacement at B. d. Rotation just to the left of B. e. Rotation just to the right of B.
For the beam shown, how does the shear change as you move from A to B? L- Select the correct response: There is not enough information to tell. It stays constant. It decreases linearly. It increases linearly
18. Replace the two forces shown by a force-couple system with the force acting at O. 360 mm 270 mm 50 N A 300 90 N