3. The equilibrium constant for the reaction of chlorine gas with phosphorus trichloride to form phosphorus pentachloride is 33 at 250°C. If an experiment is initiated with concentrations of 0.05 M PCI3 and 0.015 M C12, what are the equilibrium concentrations of all three gases? Cl:(g) + PCl,(g) = PCI:(g) a. Show a mole balance table for the given chemical reaction. Obtain the chemical equilibrium constant expression. Show the results.

3. The equilibrium constant for the reaction of chlorine gas with phosphorus trichloride to form phosphorus pentachloride is 33 at 250°C. If an experiment is initiated with concentrations of 0.05 M PCI3 and 0.015 M C12, what are the equilibrium concentrations of all three gases? Cl:(g) + PCl,(g) = PCI:(g) a. Show a mole balance table for the given chemical reaction. Obtain the chemical equilibrium constant expression. Show the results.

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter11: Nonlinear Programming

Section11.2: Introductory Concepts

Problem 3P

See similar textbooks

Similar questions

An aluminum wire having a cross-sectional area equal to 4.60 x 10-6 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s
If the crystal lattice constant is the length of the edge of the cube crystal unit in sodium, whose composition is type (BCC) equaí to (4.24A°) angstroms. What is the distance between two neighboring atoms? Calculate the sodium density if its atomic weight is (23).
The circular rod shown is made of the steel alloy AISI 4140 OQT 900. It has a diameter of 1.00 in and an initial length of 48 in. An axial tensile load of 15 000 lb. is applied during a certain operation. Compute: 1. the equivalent spring constant K, 2. the deformation X of the rod. The Young's modulus of the steel is known to be 30,000,000 psi. F=15 000 lb L= 48 in F=15 000 lb
The complex formed between Cu(I) and 1,10-phenanthroline has a molar absorptivity of 7000 L L cm-1 mol-1 at 435 nm, the wavelength of maximum absorption. Calculate (a) the percent transmittance of the solution.
Suppose we have an 80-lb lead-acid battery. 10% of the weight of the battery is active material on the plates, i.e., we have a total of 8 lb of active Pb and PbO, on the plates that can be used to make electric power. Use the Gibbs free energy method to estimate the total stored energy in the battery. Assume that the open circuit voltage for a lead-acid cell is 2.1 V. [The answer should be a little less than 1 kilowatt-hour of energy.]
3) The empirical formula of sugar is CH₂O and its molar mass is 180.2 g/mole. If one teaspoon of sugar weighs 3.50 g, how many moles of sugar and how many molecules of sugar are present? 4) A hydrate of copper(II) sulfate is 25.5% copper by mass. How many water molecules are there for each unit of copper(II) sulfate?
The coefficient of linear expansion of an metal plate is 9 x 10-6 /oC. The internal diameter of the metal plate at 20 oC is 2.2 cm. When heated, its area change, if the final diameter is 2.8 cm, what is the final temperature?
For an object of mass m=3 kg to slide without friction up the rise of height h=1 m shown, it must have a minimum initial kinetic energy (in J) of: h O a. 40 O b. 20 O c. 30 O d. 10
The displacement of an oscillating spring can be described by x = A cos(wt) where x = displacement at time t, A = maximum displacement, w = angular frequency, which depends on the spring constant and the mass attached to the spring, and t = time. Find the displacement, x, with maximum displacement A of 4 cm, for times from 0 to 120 seconds with increments of 30 seconds, and angular frequencies from 0.4 to 0.6 radians/sec, with increments of 0.1 radians/sec. The displacement for all combinations of times and angular frequencies needs to be calculated. Use meshgrid. Display your results in a matrix with angular frequencies along the top row and times along the left column like so (you may put zero, 0, or NaN, in the upper left corner:
A reservoir discharging water through sluices at a depth hbelow the water surface area Afor various values has given below: hft1011121314( . .)Asqft9501070120013501530If tdenotes time in minutes, the rate of fall of the surface is given by 48dhhAdtEstimate the time taken for the water level to fall from 14 to 10 ft. above the sluices.
Solve the following equations. Be sure to check the potential solution(s) in the original equation, to see whether it (they) are in the domain. (a) log, (r? –x – 2) = 2
Find the relative density of given liquid after taking density of given liquid & density of pure water at 4°C