3. The piston/cylinder setup as shown in the figure contains 0.1 kg of water at 1000 kPa, 500°C. The water is now cooled with a constant force on the piston until it reaches half of the initial volume. After this it cools to 25°C while the piston is against the stops. Find the final water pressure and the work and heat transfer in the overall process, and show the process in a P-v diagram. Water

3. The piston/cylinder setup as shown in the figure contains 0.1 kg of water at 1000 kPa, 500°C. The water is now cooled with a constant force on the piston until it reaches half of the initial volume. After this it cools to 25°C while the piston is against the stops. Find the final water pressure and the work and heat transfer in the overall process, and show the process in a P-v diagram. Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ammonia (an ideal gas) is contained in a 1.5 cubic meter piston. Initially, it is 200 kPa, 20C but it is compressed to 40C (at constant pressure). During this process, 1500 kJ of heat is rejected to the 20C surrounding and 750 kJ of work is done. Is this process possible?
H.W: - 0.8m of gas at 8bar and 27°C is compressed isothermally until its volume is ¼ time the original volume, then its heated at constant pressure to original volume, finally its cooled at constant volume to original condition. Find: - a- the heat transferred. b- Work done c- Change in internal energy. (draw the processes on p-v diagram) Take cp=1.01kj/kg.k, R=0.28kj/kg.k
Q3: You have an ideal gas in an insulated container. You compress it from a pressure of 40 × 105 Pa to 20 × 105 Pa, while increasing the volume from 10 to 20 m3. What is the work you done by the gas a- 10 J b- 300 J c- 500 J d- 880 J
Saturated vapor water at 200 C0 is cooled to 100 C∘ at constant pressure process. Find : 1- the final specific volume. 2- the specific work and heat transfer. 3- draw the process on a T-v and P-v diagrams.
3. In a hot water heating system, water heated to 95°C and then is pumped at the rate of 4 L/min through a radiator where it is cooled to 35°C. If the water arives at the radiator at a temperature of 85°C, how much heat in kJ does the radiator release each hour?
A piston cylinder contains 11 kg of air at 20 degC and 300 kPa. It is now heated up in a constant pressure process to 600 K. Find the final volume. (R of air = 0.287 KJ/kg K)
4. A pressure cooker (closed tank) contains water at 100°C, with the liquid volume being 1/20th of the vapor volume. It is heated until the pressure reaches 2.0 MPa. Find the final temperature. Has the final state more or less vapor than the initial state?
At the beginning, there is air in the insulated piston cylinder device with a volume of 20L at 25 degrees Celsius 250 kPa Conditions Then, by operating the heater with 220 V and 10A value for 2 minutes, the temperature of the air increases. Using the average specific heat assumption, find the temperature and the boundary work (kJ) in the final case. Air will be considered the ideal gas.
A piston-cylinder assembly contains 0.1 kg of air at 300 kPa pressure and 270C temperature. First at constant pressureBy adding heat, the volume is doubled from the initial volume. Then at constant temperature air is expanded up to 100 kPa pressure. According to this; 1-Show the whole event in the P-V diagram. 2-Status find work and heat shifts in changes.
A piston cylinder contains 11kg of air at 20 degC and 300 kPa. It is now heated up in a constant pressure process to 600 K. Find the final volume. (R of air = 0.287 KJ/kg K)
The tank of a leaky air compressor originally holds 90 L of air at 33deg C and 225 kPa. During a compression process, 4 grams of air is lost; the remaining air occupies 42 L at 550 kPa. What is the temperature of the remaining in air in degree centigrade.
In a insulated rigid container there is helium gas being stirred by a paddle wheel using 0.02 hp for 30 minutes. Initially, the gas is 80 farheinheit and 50 psia. Constant Specific heat of .753 Btu/lbm-F. What is the final temperature and the final pressure.