3.0 V across the cable, and a current of 50 A in the circuit. Draw the circuit diagram, representingthe battery as an ideal voltage source and internal resistance, and the cable and motor as resistancesin series. Using the data provided, find the resistance of each part, the motor, the cable, and thebattery, and decide if each is defective or not. You are a mechanic in a car-repair shop. You observe that the electric starting motor of a car isturning too slowly. The motor is connected to a battery of emf equal to 12 V via a cable. Your jobis to decide which parts to replace: the motor, the cable, and/or the battery?You consult the car's manual, which provides the proper operating specs for each of these parts:the battery should have no more than 0.020 2 internal resistance, the motor should have no morethan 0.200 2 resistance, and the cable should have no more than 0.040 N resistance. If any of theseresistances is exceeded, it means that the part is defective.You turn on the motor and measure the follovvoltages and currents: 11.4 V across the terminalsof the battery (note that this is not the emf, since it includes the effect of the internal resistance),

Given: Battery emf, E=12 V Terminal voltage of battery, V=11.4 V Circuit current, I=50 A Voltage…

3.0 V across the cable, and a current of 50 A in the circuit. Draw the circuit diagram, representing the battery as an ideal voltage source and internal resistance, and the cable and motor as resistances in series. Using the data provided, find the resistance of each part, the motor, the cable, and the battery, and decide if each is defective or not.

3.0 V across the cable, and a current of 50 A in the circuit. Draw the circuit diagram, representing the battery as an ideal voltage source and internal resistance, and the cable and motor as resistances in series. Using the data provided, find the resistance of each part, the motor, the cable, and the battery, and decide if each is defective or not.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

6.A purely resistive electric furnace is connected in parallel with a motor with lagging power factor less than 1.0. The combination of both charges will give an equivalent charge: a) With the same power factor as that of the motor. b) With a power factor closer to 1 than that of the motor. c) With a power factor lower than that of the motor. d) It cannot be indicated with the information provided. e) there is no solution
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
i. Draw the block diagram of a solar Photo-Voltaic system with the stand by diesel generator and explain about each component in it? ii. Discuss how you can you avoid the overcharging of the battery?
A practical switch is operating at a switching frequency of 100 kHz and a 0.5 duty cycle. The switch is initially on (the first half cycle). The switch has the following parameters: Von = 0.1 V Volt 80 V Ion - 100 A 10.1 A ton = 0 Loft O Ldelay O a) Draw clear voltage and current waveforms for one switching cycle with all values shown (times, voltages, currents, etc.). b) Find the average power loss in one switching cycle.
An electric motor (with an efficiency of n1 = 90%) drives a belt (n2 = 85%) that is connected to a generator (n3 = 92%) that produces electricity for an incandescent ligl (n4 = 5%). Improving the efficiency of this part would greatly increase the overall system efficiency: O The Incandescent Light O The Belt O The Generator O The Electric Motor
Post Test Choose the letter of the correct answer. Write the chosen letter on a separate sheet of paper. 1. It is a smail component that lights up when current flows through it. a. Capacitor 2. It regulates the amount of current flowing in an electronic circuit. a. Capacitor 3. These are devices or components which do not require an external source to their operation. b. Fuse c. LED d. Resistor b IC c. Inductors d. Resistor c. passive devices d. electrical devices a. active devices b. electronic components 4. It is a three-terminal active component that is used mainly in boosting or amplifying electrical signals; both AF and RF ranges. a. Capacitor 5. it is necessary to turn the electrical circuit "on" or "off" a. Fuse 6. Testing tools that are capable of executing tests, reporting outcomes, and comparing results with earlier test runs a. Automated 7. The testing method that starts a soon as code is written and continues in successive stages as code is combined with other units of…
12. How is the A-hr capacity of a lead-acid battery determined?
A good rule-of-thumb to estimate the expected life of a motor, a ballast, or other electrical equipment is that for every ____________ C above rated temperature, the expected life will be cut in __________________.
QI/ Choose the correct answer 1.When the coil of Relay is supplied with 12 volts, the common will a) reverse from NO. to NC. b) reverse from NC. to NO. c) stand still. d) damage the coil. 2. The forward voltage drop across a silicon diode is about . a) 2.5 V b) 3 V c) 10 V d) 0.7v 3. Zener diodes are also known as a) Voltage regulator b) Forward bias diode c) Breakdown diode d) None of the mentioned 4. A zener diode works at a) Forward bias. b) Reverse bias. c) 12 volts. d) 220 volts 5.Capacitor stores which type of energy? a) kinetic energy b) vibrational energy c) potential energy d) heat energy after long time. 6. Capacitor blocks a) alternating current b) direct current c) both alternating and direct current d) neither alternating nor direct current 7.when installing an ammeter, you should a) Connect it parallel with the component to be tested b) Install the instrument in series with current path c) Place a resistor in series with the ammeter to prevent damaging the device. d) Set…
Give a detailed description of an expirment about 'D'Arsonval Meter Movement as DC ammeter'.Support your answer with pictures and examples.
In an energy meter, creep speed is the speed of the aluminium disc's at O a. Full load condition O b. Over load condition O c. Half load condition O d. None of the above
What is the coupling field used between the electrical and mechanical systems in energy conversion devices? a) Magnetic field b) Electric field c) Magnetic field or Electric field d) None of the mentioned