3.1-8. The WorldLight Company produces two light fixtures (prod- ucts 1 and 2) that require both metal frame parts and electrical components. Management wants to determine how many units of each product to produce so as to maximize profit. For each unit of product 1, 1 unit of frame parts and 2 units of electrical compo- nents are required. For each unit of product 2, 3 units of frame parts and 2 units of electrical components are required. The com- pany has 200 units of frame parts and 300 units of electrical com- ponents. Each unit of product 1 gives a profit of $1, and each unit of product 2, up to 60 units, gives a profit of $2. Any excess over 60 units of product 2 brings no profit, so such an excess has been ruled out. (a) Formulate a linear programming model for this problem. p (b) Use the graphical method to solve this model. What is the resulting total profit?

3.1-8. The WorldLight Company produces two light fixtures (prod- ucts 1 and 2) that require both metal frame parts and electrical components. Management wants to determine how many units of each product to produce so as to maximize profit. For each unit of product 1, 1 unit of frame parts and 2 units of electrical compo- nents are required. For each unit of product 2, 3 units of frame parts and 2 units of electrical components are required. The com- pany has 200 units of frame parts and 300 units of electrical com- ponents. Each unit of product 1 gives a profit of $1, and each unit of product 2, up to 60 units, gives a profit of $2. Any excess over 60 units of product 2 brings no profit, so such an excess has been ruled out. (a) Formulate a linear programming model for this problem. p (b) Use the graphical method to solve this model. What is the resulting total profit?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

problem : Excessive use of electronic devices relate this problem to Sustainable Development Goals # 12 ( responsible consumption and production)
Product A consists of two units of Subassembly B, three units of C, and one unit of D.B is composed of four units of E and three units of F. C is made of two units of H andthree units of D. H is made of i ve units of E and two units of G.a. Construct a simple bill-of-materials (product structure tree).b. Construct a product structure tree using low-level coding.c. Construct an indented parts list.d. To produce 100 units of A, determine the number of units of B, C, D, E, F, G, and H required.
A package of frozen fish sticks have different instructions when they are heated up on the stove as compared to using the oven. Stove: Heat over medium flame for 2 minutes. Then flip the fish sticks (turn them over) and heat them for another two minutes. Oven: Preheat the oven to 375 F. Put them on a metal baking sheet for 15 minutes. a. Explain why the instructions have you flip the fish sticks over when you’re heating them with the stove, but not with the oven. b. If you follow the oven instructions, the side of the fish sticks touching the metal baking sheet will cook more than the top side of the fish sticks. Explain why.
Based on the table below, which of the statements below is/are correct regarding the 3D printing process shown in the schematic? a.You can produce a room-temperature non-fragile 225C oven-safe food container with at least one material from the above table using this process and a 280C nozzle b.You can use this process to print plastic or brittle objects but not elastomers and rubbers c.Manufacturing a thermoplastic HDPE hose with an extrusion nozzle heated to 175C is possible with this process d.You can print thermoplastic and thermoset polymers with this process, you only need to make sure that the nozzle specs and the crosslinking conditions match the polymer requirements e.This process is best suited for the low volume production of tubes, bars and beams due to the nature of the extrusion process
(b) A production line consists of below tasks. 1. Place material A to conveyor 2. Weld material A and material B 3. Inspect the result of (2) 4. Place the finished product to the multilayer storage Design the automations that can perform above process and give a short description about your automations.
what are the main activities of Intuit Inc?
what is the technique of direct integration conventiontly used for
MENG364 MANUFACTURING TECHNOLOGY
Figure below shows a MEMS released device. Develop a process sequence for fabrication of this device. You may choose materials (metal types, insulators) but you have to use a compatible fabrication sequence for the whole process.
Can you give me a detailed description on their uses and function 1: Helmet 2: Protective clothing 3: safety shoes 4: Ear muff 5: Hand gloves 6: goggles 7: Chemical suit 8: Face mask 9: Safety harness 10: Welding shield
Based on the table below, which of the statements below is/are correct regarding the 3D printing process shown in the schematic? Z AXIS X AXIS YAXIS LEGEND A: Extruder B: Nozzle C: Printed part D: Hot plate E: Filament Table 15.2 Melting and Glass Transition Temperatures for Some of the More Common Polymeric Materials Material Polyethylene (low density) Polytetrafluoroethylene Polyethylene (high density) Polypropylene Nylon 6,6 Polyester (PET) Poly(vinyl chloride) Polystyrene Polycarbonate Glass Transition Temperature [°C (°F)] -110 (-165) -97 (-140) -90 (-130) -18 (0) 57 (135) 69 (155) 87 (190) 100 (212) 150 (300) Melting Temperature [°C (°F)] 115 (240) 327 (620) 137 (279) 175 (347) 265 (510) 265 (510) 212 (415) 240 (465) 265 (510) a. This process is best suited for the low volume production of tubes, bars and beams due to the nature of the extrusion process b. Manufacturing a thermoplastic HDPE hose with an extrusion nozzle heated to 175C is possible with this process □c. You can…
Please provide steps on how to derive the output of each container.