= 3.21 You must cool 78 kg/min of a 60%-by-mass mixture of glycerin in wa- ter from 108°C to 50°C using cooling water available at 7°C. Design a one-shell-pass, two-tube-pass heat exchanger if U 637 W/m²K. Which side should the water flow through? Explain any design decision you make and report the area, TH₂0out and any other relevant features.

= 3.21 You must cool 78 kg/min of a 60%-by-mass mixture of glycerin in wa- ter from 108°C to 50°C using cooling water available at 7°C. Design a one-shell-pass, two-tube-pass heat exchanger if U 637 W/m²K. Which side should the water flow through? Explain any design decision you make and report the area, TH₂0out and any other relevant features.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.41P

See similar textbooks

Similar questions

Mot water is used to heat air in a double-pipe heat exchanger as shown in the following sketch. If the heat transfer coefficients on the water side and on the air side are 550W/m2Kand55W/m2K respectively, calculate the overall heat transfer coefficient based on the outer diameter. The heat exchanger pipe is 5-cm, schedule 40 steel (k=54W/mK) with water inside.
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol What is the a.) value of G in kg/s.m2? b.)value of friction factor? 3 significant figures c.)the % of pressure drop? d.)the outlet pressure? e.) compressible or not?
1. 400,000 Ibm/hr of 270°F water is to be heated to 370°F by condensing saturated 390°F steam. (The steam does not sub cool upon condensing). Your job is to design the heat exchanger. The following parameters represent constraint your design. number of tube passes 4 tube fluid water being heated number of shell pass shell fluid steam being cooled U (based on outside tube area) 700 BTU/hr – ft² – °F 1 in tube outside diameter tube wall thickness 1/16 in bulk tube fluid velocity 5 ft/s (a) How many tubes are required per pass? (b) How many tubes are required total? (c) Allowing 3 ft for headers and flanges, how long should the exchanger be?
what overall thermal system is this for in reference to part 1 , also could you also use numbers from a source for part 2 and do the calculations that way with actual reliable numbers , to make things easier to understand. And also part 2 is not complete as you need to complete performance optimisation of heat exchangers.
Q#01: Write a short note on the following: What are the best possible solutions to increase the heat transfer rate of a body? Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer. Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate? Which of the following Fins/Heat exchanger will transfer more heat and why? Justify your answer. Flat plate. Circular/pin fins. Triangular fins.
4. The following heat exchanger uses 10 kg/s of hot air to heat and boil liquid water into saturated steam at 500 kPa. (a) Find the steam flow (kg/s) (b) Determine whether the process is allowed by the second law (Answer: It is not!) (c) On the surface, the process looks OK as Tair>Twater at both the inlet and outlet. You should be able to see the problem if you sketch the air and the water temperature profiles as you move left to right through the exchanger. (Hints: The air will be essentially a straight line, while the water will not. For the water, think about what happens when it is changing phase.) This is called a pinch point violation, and it is a very important design consideration in advanced combined cycle systems and in nuclear power plants. Air 100 kPa 160°C 10 kg/s Saturated Vapor 500 kPa Air: 160°C Steam: 151.8°C Q Air 100 kPa 30°C Liquid Water 500 kPa, 20°C Air: 30°C Water: 20°C
Design a hydrocooling unit to cool down fruits and vegetables from 30 °C to 5 °C in 20 minutes at a rate of 20,000 kg of fruit or vegetables/h. The design must fulfill the following requirements: The unit will be an immersion flooded system. It must be able to cool down and transport the products in chill water. The tank has the following dimensions approximate. three meters wide and up to 90 cm hight. The water will circulate and be cooled through the evaporation section of a refrigeration system. The refrigerant temperature inside the coils will be -2 °C, and the water temperature must not drop below 1 °C and must not exceed 6 °C. Assuming reasonable values for the average density, specific heat, and porosity of the product (the fraction of the volume of air in a box), recommend reasonable values for: The speed of the water through the canal, the capacity of the cooling system. the compressor power.
A Copper ball at 40'Cis dropped in a mug containing water at 40°C. The heat will Select one: O a.not flow from Copper ball to water or from water to Copper ball O b. flow from Copper ball to water O c. Increase the temiperature of both O d. flow from water to Copper ball
The temperatures of the 20 ºC 25 ºC 30 ºC water at outlet Task 2 Derive the Steady Flow Energy Equation from the first principles
In a heat exchanger, water flows through a long copper tube (inside diameter 2.2 cm) with an average velocity of 2.13 m/s. The water is heated by steam condensing at 150 degree celsius on the outside of the tube. Water enters at 15 degree Celsius and leaves at 60 degree Celsius . What is the heat transfer coefficient, h, for the water? Write the given, required and solution
3. A 2-shell 4 tube pass HE will be used to cool a hot fluid from 400oC to 200oC using a cooling water available at 80oC and heated at 180oC. Calculate the total heat transferred if the tubes are 50mm med wt. steel, 5 m long per pass. Assume hi = 200W/m2K and ho = 4500W/m2K
Hello! I'd like help with the following exercise, from Levenspiel's "Engineering Flow and Heat Exchange". Leftover air at 20ºC and 100kPa is driven by a fan through a horizontal galvanized conduit of 1 m in diameter and 10m in length at a speed of 10 m/s. What size motor should be used if its efficiency is 90% and that of the fan is 20%? I'm not sure where to start. My professor hasn't explained much about this subject.