300 mm FN kN SN kN-mm 250 mm MN kN SN kN FN kN 200 mm 100 mm FN kN 25° 150 mm Compute the following in vector form A. The resultant forces [resultant] B. Moment at MN kN force [momenta] ALVIN (FN) = 1+12+ 23 +9 + 14 = 59 NAVALTA (MN) = 14 + 1+ 23 +1+ 12 + 21 +1 = 72 DELIRO (SN) = 4+5+12+9+19 + 16 = 65

300 mm FN kN SN kN-mm 250 mm MN kN SN kN FN kN 200 mm 100 mm FN kN 25° 150 mm Compute the following in vector form A. The resultant forces [resultant] B. Moment at MN kN force [momenta] ALVIN (FN) = 1+12+ 23 +9 + 14 = 59 NAVALTA (MN) = 14 + 1+ 23 +1+ 12 + 21 +1 = 72 DELIRO (SN) = 4+5+12+9+19 + 16 = 65

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

а a 17 - B b Find the center of gravity M (x, y, z) of the three-dimensional homogeneous ABCD wire in the figure by using the coordinate set. The dimensions of the wire are a= 15 cm, b= 27 cm. In which of the following options are the coordinates of the BC part of the homogeneous wire in the x, y and z axes given correctly? O a) (27; 7.5 ; 15) O B) (27; 15 ; 7.5) OC) (13.5 ; 7.5 ; 0) OD) (13.5 ; 15 ; 15) O TO) (27; 7.5 ; 0)
View Policies Current Attempt in Progress Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. 200 N Answers: R= 285 N i d = M = i Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. Single resultant force. 150 N 690 mm 690 mm 690 mm N N-m mm
Determine the intenal normal force, shear force, and moment at point Cin the simply supported beam. Point Cis located just to the right of the 250 Nm couple moment. * Make sure to add units out of ** Your answer should look like this: Ne =, Vc=. Mc 100 N 5 m 300 N/m A 35 250 N.m 8 m 4 m 4 m 40 N Answer
PROBLEMS Introductory Problems 2/1 The force F has a magnitude of 500 N. Express F as a vector in terms of the unit vectors i and j. Identify the x and y scalar components of F. Ans. F = 383i - 321j N, F, = 383 N, F, 321 N %3D 40 F = 500 N
QUESTION 4: LONG QUESTIONS Which of the following forces in the Figure below has the moment about point A equals 54 Nm, Anticlockwise ..? (NB. Each section represents 9 m"). NB. Elaborate on your answer in terms of calculations. 10N 8N 34 N15 12 26 N
Q4 / what's the value of C that make the vectors ( ci – 2k – k ) , ( i – j + 2k ) Orthogonal .
Find the Maclaurin Series of the following functions. 1 sin(x?) sin(x) 3 arctan(x) 4 cos (x) 5 x'e* V1- x3
QI/ The rigid pole and cross-arm assembly is supported by the three cables shown. A turnbuckle at D is tightened until it induces a tension T in CD of 1.2 kN. Express T as a vector. Does it make any difference in the result which coordinate system is used? Ans. T = 0.321i + 0.641j – 0.962k kN, IC 1.5 m B 1.5 m G T= 1.2 kN 3 m 2 m 1.5m 3 m
Suppose that d = 0.14 m in (Figure 1). Part A Determine the angle at which the 500-N force must act at A so that the moment of this force about point B is equal to zero. Express your answer in degrees to three significant figures. 0= Submit VE ΑΣΦ | 41 Request Answer Figure vec 1 m B ISWE ? 2 m-
X Q3/ write force F as Cartesian Vector. Also find: 1. The moment of a force about point O. 2.The moment of a force about z-axes. Z 0.3 m 120° 45° F = 200 N 60° 0.25 m y
Force F= 2,000 N acts from A towards B. 275 mm A 550 mm 220 mm Determine the moment of the force about point C in N m. (The line of action for F does not pass through O. That illusion occurs due to the isometric drawing. Express your answer in vector form.) N-m Determine the shortest distance from point C to the line of action of the force in mm. mm
What is the reaction force at 'A' alongy- axis? (note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative for down. Ay = -4m 4m D 450N 4m A 000 В