318. A solid compound shaft is made of three different materials and is subjected to two applied torques as shown in Fig. P-318. (a) Determine the maximum shearing stress developed in each material. (b) Find the angle of rotation of the free end of the shaft. Use G. 28 GN/m², G, = 83 GN/m², and G, = 35 GN/m2. 100 mm dia. 75 mm dia. 4.0 kN 1.5 kN m Aluminum Steel Bronze -3 m- 2 m 1.5 m

318. A solid compound shaft is made of three different materials and is subjected to two applied torques as shown in Fig. P-318. (a) Determine the maximum shearing stress developed in each material. (b) Find the angle of rotation of the free end of the shaft. Use G. 28 GN/m², G, = 83 GN/m², and G, = 35 GN/m2. 100 mm dia. 75 mm dia. 4.0 kN 1.5 kN m Aluminum Steel Bronze -3 m- 2 m 1.5 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

3. The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500N -m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm 4. A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 x 106 psi for aluminum. +4 in. → 0.04 in. 0.08 in.´ 5. Two steel springs are arranged in series as shown. The upper spring has 36 turns of 100-mm- diameter wire on a mean radius of 350 mm. The lower spring consists of 24 turns of 75-mm diameter wire on a mean radius of 245 mm. If the ultimate shearing stress in either spring must not exceed 692 MPa, (a) compute the maximum value of P and total elongation using factor of safety equal to 1.5. (b) What is the equivalent spring constant? Use G = 83 GPa. 2 of 2 4 in. wwwww.-
Figure 2 shows a solid shaft consisting of two prismatic circular parts in equilibrium under the torques applied to the pulleys fastened to it. Give that the diameter for part AB and BC are 200 mm and 120 mm, respectively. (a) Determine the torque, TR on the shaft. (b) State the segment at which the maximum shearing stress occurs. Verify your answer by shear stress analysis. d- 200 mm d- 120 mm TA= 36 kN.m Te=14 kN.m Ta C Figure 2: Solid shaft with pulleys
What is the minimum diameter of a solid steel shaft that will not twist through more than 3.18 degrees in a 6 m length when subjected to a torque of 14KN-m. What maximum shearing stress is developed? Use G=83GN/m^2.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3˚ in a6-m length when subjected to a torque of 15 KN-m? What maximum shearing stress isdeveloped? Use G=85 GPa.
1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 Ib-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.
1) What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6 meter length when subjected to a torque of 14k N.m?What maximum shearing stress is developed ?Use G=83GPA.
What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3° in a 7-m length when subjected to a torque of 10 kNm? What maximum shearing stress is developed? G = 75 GPa
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
For the solid circular rods exposed to the shown torques, determine the segment that experiences maximum shearing stress. Would drilling a 10-mm diameter hole through the center of that segment help in decreasing the stress? 100 N. m 160 Nm C B 80 N.m A dвc dAB = 30 mm dcD = 70 mm = 50 mm
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A hollow circular steel shaft with an outside diameter of 2.569. and a wall thickness of 0.388 in. is subjected to a pure torque of 292 lb-ft. The shaft is 124 in. long. The shear modulus of the steel is G-12.000 ksi. Determine the magnitude of the angle of twist in the shaft. 1. T B
Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m %3D 2 m 100 mm 50 mm T= 50 kN. m