4- The following serial data are applied to the Flip - Flop below. Determine the resulting serial data that appear on the Q output. There is one clock pulse for each bit time. Assume Q is initially 0. J;: 1001101 K: 0001110 =D J J;: 0111010 K:1101100 CK J;: 1111000 K:1010101 14

4- The following serial data are applied to the Flip - Flop below. Determine the resulting serial data that appear on the Q output. There is one clock pulse for each bit time. Assume Q is initially 0. J;: 1001101 K: 0001110 =D J J;: 0111010 K:1101100 CK J;: 1111000 K:1010101 14

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Q: A. Design a 3-bit binary counter using T flip-flops and gates which counts in the sequence of…

Q: Design a 3-bit binary counter using T flip-flops and gates which counts in the sequence of…

Q: (a) A D Flip-Flop is sometimes used to introduce a delay in a logic circuit, so that the output…

Q: Design synchronous counter using JK flip flops to count the following binary numbers 0000 ,…

A: We have to design synchronous counter using JK flip flops to count the following binary number:…

Q: Design the synchronous counter that counts these digits 0 1 2 4 5 6 8 using JK flip-flops

Q: How many flip-flops will be needed when following synthesized? codes ar always @(posedge clk) begin…

A: A flip flop is used to store 1 bit of information to store series of data registers are used. Always…

Q: Design a 3-bit binary counter using T flip-flops and gates which counts in the quence of…

Q: Design a 3-bit synchronous counter that counts odd binary numbers, ie (001,011,101,111 & then goes…

Q: Design a 3-bit binary counter using T flip-flops and gates which counts in the sequence of…

Q: We wish to design a digital system with two flip-flops, say B and C, and one 4-bit binary counter A,…

A: To Design a digital system with two flip-flops To counter bits A3 and A4 determine the sequence of…

Q: D- D1 Q1 Data Path D2 Q2 FF1 FF2 CLKA CLKB Routing Delay SYSCK For a given sequential circuit as…

A: Flip flop is a latch with additional control input (clock or enable ). A flip flop is used to store…

Q: A. Design a 3-bit binary counter using T flip-flops and gates which counts in the sequence of…

Q: 2- Using JK Flip flops, a 2-bit counter will be designed that will count down ((11-10-01-00) when…

A: 1. The characteristic table of J-K flip flop is J K Qn+1 0 0 No change 0 1 0 1 0 1 1 1…

Q: Q6. For the following state graph, construct a transition table. Then, give the timing diagram for…

A: State diagrams are regularly used to represent the dynamic conduct of structures. The circles in a…

Q: 1. A clock signal is usually a continuous triangular wave that serves as another hput to a memory…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: 1. Convert SR flip-flop to JK flip-flop. 2. The following serial data have been applied to the…

A: The flipflop of one type can be realised by using another type. The output of flipflop can be…

Q: Design a two bit synchronous counter that count the sequence 0,1,2 using T flip flop

Q: Use AND gates, OR gates, inverters, and a negative-edge-triggered D flip-flop to show how to…

A: We have to create JK Flip-Flop using D Flip Flop, using a negative-edge-triggered D flip-flop,…

Q: List the binary output at Q for the flip-flop of followed Figure

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: Q5 A Moore machine is to detect three or more consecutive zeros on an input bitstream using D flip…

A: The solution is given below

Q: Using T flip flops, design a 3 bit counter which counts in the sequence: 111, 110, 101, 100, 011,…

A: We need to design 3 bit counter which counts in the sequence:…

Q: Design of a digital electronic circuit that produces 4 bits of binary numbers sequentially and…

Q: Design Asynchronous counter using negative edge J-K flip flop to count the following states ( 10→…

A: Here the properties of JK flipflop has been used to solve it. Here number of bits or flipflop needed…

Q: In the standard POS expression, the binary words are formed by representing each complemented…

A: In the standard POS expression, The binary words are formed by representing each non-complemented…

Q: A 4-bit ripple counter consists of flip-flops, which each having a propagation delay from clock to Q…

Q: Answer the following: JO a) Given the Circuit 1 shown to the right, provide the output Q for the…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: 2. Determine the Q waveform for the flip-flop as seen in the figure below. Assume that Q = 0…

Q: How to connect these boolean expressions to CD4027 with 555 timer Jk flip flop 1 Ja = BCD Ka = D…

A: According to the question, we need to design a circuit diagram by using CD4027 IC for the given…

Q: 7−bit shift register using JK ﬂip-ﬂops

A: Shift Register It is a type of sequential logic circuit that can be used for the storage and…

Q: Discussion 1. For a master-slave J K Flip - Flop with the inputs below, sketch the Q output…

Q: 2. Determine the Q waveform for the flip-flop as seen in the figure below. Assume that Q = 0…

A: In this question, We need to draw the output waveform of the JK filp flop. If initially Qn = 0

Q: 8-2-5-1

A: Here It is asked to design T flipflop where the present states and next states are given. Here to…

Q: 4. Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t +…

A: Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t+1) =…

Q: Write the vhdl code for 4-bit shift register using d flip flop Write the code using boolean…

A: library ieee; use ieee.std_logic_1164.all; entity sipo is port( clk, clear : in std_logic;…

Q: Find the binary assignment table for the following circuit, then re-design it using JK flip flops.…

A: For the given logical circuit, binary assignment table is drawn, which shows that Output is set only…

Q: Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The…

Q: Design a 3-bit synchronous counter that counts even binary numbers, i.e (000,010,100,110 & then goes…

Q: Using T flip flops, Implement a 3-bit asynchronous binary counter.

Q: 4. Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t +…

A: Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t+1) =…

Q: A. Design a 3-bit binary counter using T flip-flops and gates which counts in the sequence of…

Q: An asynchronous state machine has two inputs (X1 and X2) and one output (Z). he output is the same…

Q: 1. Construct the SR Flip Flop circuit shown in Figure 5.1. PRE iIs equal to SET and CLR is equal to…

A: From the above question the diagram is shown below:

Q: Draw the circuit, and show the truth table, for the clocked Master-Slave JK ﬂip-ﬂop

A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…

Q: Time le Use T flip-flops and gates to design a binary counter with the repeated binary sequence: 0,…

Q: Create a 5-bit shift right register using D flip-flops. Given an initial value of Din=1 and Q4 Q3 Q2…

Q: By giving the truth table of the JK Flip Flop, determine how the Q and Q outputs will take value in…

A: By giving the truth table of the JK Flip Flop, determine how the Q and Q outputs will take value in…

Q: Follow correct label names: · Q0, Q1 - prev/present states · DO, D1 - D-FF names • X - input - Y-…

A: State diagrams

Q: Design a counter to produce the following binary sequence. Use J-K flip-flops. 0,9, 1, 8, 2, 7, 3,…

A: counting sequence is 0,9,1,8,2,7,3,6,4,5,0 repeats..

Q: a. ABCD=1010, Write the value of the shift register after applying three clock pulse. (D-flip flop)…

Q: The Figure below shows a simple Moore sequence detector with an external input X. 1. Design this…

Concept explainers

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.

Question

4- The following serial data are applied to the Flip - Flop below.
Determine the resulting serial data that appear on the Q output.
There is one clock pulse for each bit time. Assume Q is initially 0.
J;: 1001101 K: 0001110
=D
J
J;: 0111010 K:1101100
CK
J;: 1111000 K:1010101
14

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 4 a) The IEEE Standard 754 representation of a floating point number is given as: 01101110110011010100000000000000. Determine the binary value represented by this number. b) Convert each of the following hexadecimal values to binary. i) AB1916 ii) 2DEF16 iii) 8A4516 iv) 9B5A16 c) If a computer's system clock is 2.4 GHz, calculate the period of the system clock. d) If an 8-bit binary number is used to represent an analog value in the range from 200 ounces to 700 ounces, what is the resolution of the system?
1What will be the state of a MOD64 counter after 90 input pulses if the starting state=000000?A.100100B.011010C.010110D.011100 2.A MOD 32 counter is holding the count 101112. What will the count be after 31 clock pulses?A.10100B.10010C.10000D.10110
Assuming even parity, find the parity bit for each of the following data units. a. 1001010 b. 0001101 c. 1000000 d. 1110111
Consider the binary number 110110012. Find the equivalent decimal number.
H.W 1. Convert SR flip-flop to JK flip-flop. 2. The following serial data have been applied to the flip-flop. Assume Q = 0 initially and there is one clock pulse for each bit. Determine the output sequence. K J,-10101 101 K, - I100101 J2 =11000110 K2 = 10101011. 15
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate thecomplete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform.(Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.)(Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…
(a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits, which shift register I should explain it with the help of circuit diagram and table. (b). Write comparison between Diode transistor logic and Transistor Transistor logic
Please show on the clock signal how the binary code follows: 0000, 0001, 0010, ...
Determine the total time required to serially transfer the eight bits contained in waveform A of Figure the first to be transferred. The 1 MHz clock is used as reference. and indicate the sequence of bits. The left-most bit is Clock A
(a) Perform binary addition of the following numbers: 110111101.10011 + 100010101.11110 (b) Represent the decimal number 66245 in BCD format and calculate how many nibbles are there in this BCD number. (c) Convert the following (i) (01100.01000)2 to Decimal (ii) (015.63)10 to Octal
Write an 8051 C program to get a byte of data form P0. If it is less than 100, send it to P1 otherwise send it to P2.