4. A 375.00 ft. line is to staked-out with a steel tape (fully supported) inside a warehouse. The tape is to be pulled at 10 lb. The tape is known to be 100.012 ft. long when pulled at 25 lb at 68 degrees F. The tape weighs 1 lb. The cross-sectional area of the tape is 0.0030 sq. in. The elastic modulus is 29,000,000 psi. The temperature inside the warehouse is 68 degrees. What distance on the tape must be used to stake the line?

4. A 375.00 ft. line is to staked-out with a steel tape (fully supported) inside a warehouse. The tape is to be pulled at 10 lb. The tape is known to be 100.012 ft. long when pulled at 25 lb at 68 degrees F. The tape weighs 1 lb. The cross-sectional area of the tape is 0.0030 sq. in. The elastic modulus is 29,000,000 psi. The temperature inside the warehouse is 68 degrees. What distance on the tape must be used to stake the line?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 20°C under a 50 N pull supported at both ends. During measurement, the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured on 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm? and the coefficient of linear expansion is 0.000016 m/ºC. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.
Q1. Find: (a) the stress in the Steel and Aluminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. Co) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 11.2 195 35 Aluminium 300 18.9 30 90 Aluminium Steel 4m t 2m
A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005m. long at 20°C under a 50 N pull supported at both ends. During measurement, the temperature is 5°C and the tape is suspended under a 75 N pull. The line is measured on 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3mm? and the coefficient of linear expansion is 0.000016m/°C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance c. What is the true horizontal distance.
(40 H.wA Rismatic steel bar of a Square cro ss section (lookloo)mm is locoled by compressive forcc P= 1300 k, the bar has length 2.5 m, =200 G Pa, V=0.3, determine the Shortening S, the Incrense in the dimensions of cross Section, the change In Volume DV of the bar? 7. loomm loomm
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000
note: SN is equal to 18, topload will be equal to 118kN.
The assembly is subjected to a vertical shear of V=55 kip Figure B- 2 in. 0.5 in. 0.5 in. 6 in.. 2 in. 0.5 in. 6 in. < 1 of 1 0.5 in. 0.5 in. Part A Determine the shear flow at point A (Eigure 1) Express your answer with the appropriate units. 9A= Submit Part B μA 9B = Value Request Answer HÅ Determine the shear flow at point B Express your answer with the appropriate units. Value lb in ● Submit Request Answer - 1) ? B ? lbin-1)
A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the beam if the working stress in bending is 15 MPa. w = 3 kN/m 5kN Cross-section 1kN.m b 1m Upload 250mm Choose a File 1m E 2m
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
270 KN Collar 1. The round bar shown in the figure has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C, and D. If the allowable axial stresses are 125MPa in the steel, 70MPa in the brass, and 85MPa in the aluminum, determine the diameters required for each of the sections Assume that the allowable stresses are the same for tension (T) and compression (C). Include Solution and Free Body Diagram. Steel 245 KN -0.5m- Brass 100 mm 150 mm Bell crank 200 kN. -0.5 m C Aluminum D -0.5 m Support bracket- 25 mm 2. A vertical shaft is supported by a thrust collar and bearing plate as shown in the figure. Determine the maximum axial load that can be applied to the shaft if the average punching shear stress in the collar and the average bearing stress between the collar and the plate are limited to 75MPa and 100MPa, respectively. Include Solution and Free Body Diagram. 6 mm 225 KN Description Internal axial force on steel section, Rs= Internal axial force on…
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
can someone please help me with this? Thank you -) A short square steel structural tube is used as a compression member and is subjected to an axial load.Axial deformation is 0.004 inches. What is the load?