Note that although part c's solution has been given, please show all the work necessary to arrive at that equation. Work is also required for part a and part b. 4. Consider the following system, which has a variable supply pressure pinPaHP1PinR₁Tank Area: AR₂gout Pa(a) Find the impedance network that describes this system, considering på as ground.(b) Find the transfer function P₁(s)/Pin(s).(c) Find an equation that the parameters R₁, R2, A, p, and g should satisfy in order that the stepresponse settling time t, < 10s 4.(R₁+R₂)pgR₁ R₂A> 0.46

Answered: Image /qna-images/answer/ca18d934-bb71-4fc2-8125-1388c692203f.jpg

4. Consider the following system, which has a variable supply pressure pin F Pin R₁ P1 Tank Area: A R₂ * gout Pa (a) Find the impedance network that describes this system, considering på as ground. (b) Find the transfer function P₁(s)/Pin (8). (c) Find an equation that the parameters R₁, R₂, A, p, and g should satisfy in order that the step response settling time t, < 10s

4. Consider the following system, which has a variable supply pressure pin F Pin R₁ P1 Tank Area: A R₂ * gout Pa (a) Find the impedance network that describes this system, considering på as ground. (b) Find the transfer function P₁(s)/Pin (8). (c) Find an equation that the parameters R₁, R₂, A, p, and g should satisfy in order that the step response settling time t, < 10s

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

google.com/forms/d/e/1FAlpQLScF2Wzu92iVI-tEM2nxdhqXrGdR460G4QCTxaUZZeC678PqTg/formResponse مطلوب /06 *:The potential at point P due to Q1 and Q2 is Q, = 1x10-12C 0.5 m 0.5 m Qz = 1x10-12C %3D 50 cm 0.01797 V Ov O -0.01271 V O 0.01271 V O Insert PIC F10 F11 F12 F6 F7 FB Backspace 9 € P Enter H
1. What impedance vector 0 – j22 represents:A. A pure resistance.B. A pure inductance.C. A pure capacitance.D. An inductance combined with a resistance.
2_53528980697... -> For the circuit shown below, detemine the voltage of the -j10 2 capacitive reactance. -j5 0 ILOA(T) ==j102 jlon is Q 102 O 0.5L-90 52 A.
Complete solution.
1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?
SHOW COMPLETE SOLUTIONNNN
I. SOLVE THE FOLLONING PROBLENS : A COPPER WIRE OF 0,3 Mm RAAUS HAS A LEN ETH OF 1. JOM- IF THE RESISTIVITY of cOpPER IS 1-7 x0 WHAT WOULD BE THE RESISTANOE OF THE WIRE? OF A 100m WIRE IS 1035 mm AND 3.7 OHMS. WHAT 2. THE DIAMETER THE REISTANCE IS IS THE CONDUCTIVITY 3. WHAT WILL BE THE VALUE OF A CAPACITOR WHEN IT HAS A CAPACITIVE REACTANCE OF 300R ANP to A 6o HZ. SUPPLY? IN FARADS IS CONNECTED 4. WHAT Is THE VALUE OF THE RESISTOR WITH THE FOLLOWING COLORS ? A. BROWN, BLACK, GOLD, REP B. BLUE YELON BROWN, SILVER PED, SILVER, BROWN, VIOET C. 5. AND t WHEN V 220V AND R= 50n WHEN I = 45 A WHEN V = 120V FIND V ANO R 80n AND AND E= 11A-
Show complete solution:
Given circuit, capacitor voltage is at 0 V with switch SW1 open. At time t0, switch SW1 is closed. At time t0, what is the voltage v? What is the voltage v at time infinity? At time t0, what is the current through R2? What is the current through R2 at time infinity?
5. Find the capacitor voltage in the network shown in figure. If the switch closes at t-0. Assume zero initial conditions. Also find the time constant, rise time, and settling time for the capacitor voltage 1=0 ww 1.802 0.79 F
Calculate capacitance Cand voltage U over resistance. What is the peak value of resistance's voltage? Voltage source e(t) = ésin(wt + 45°). Resistance R-50, circuit's total reactance X-50, inductance L =50mH, ê -40V and frequency f =50Hz. R L Give the answers to one decimal place. Do not write numbers in the complex number form! Absolute value of voltage source (RMS value): V Total impedance of circuit (absolute value): Capacitance: μF Absolute value of current (RMS value) supplied by voltage source: Phase angle of current: degrees Peak value of resistances voltage: 22 A
The network Nc shown below in Figure 1.99(a) contains a combination of scaled capaci- tors in series and parallel connections. Using the vahues as shown, you are asked to do the following. (a) Calculate the value of the terminal capacitance Cab at terminals a-b. (b) To obtain an equivalent capacitance Ceq of 1.5F, Nc is to be placed either in series with a capacitance Cz as shown in Figure 1.99(b) or in parallel with Cx as shown in Figure 1.99(c). Determine which connection is correct and calculate the value of C; that will produce the value of 1.5F for Ceg- 4F 2F 3F 1F C OF (a) N. N. 2. (b) (c) Figure 1.99 (a) Capacitor combo Nc (b) Nc in series with C, (c) Ne in parallel with C,