4. Testing, adjusting, and balancing is a prerequisite before starting-up of an air-conditioning system used for public areas. To perform this, it is needed to measure the flow rate available within the system. What would you prefer to use in such a measurement? A) Pitot- static Tube B) Thermal (Hot-Wire and Hot-Film) Anemometers C) PIV D) Pitot Tube

4. Testing, adjusting, and balancing is a prerequisite before starting-up of an air-conditioning system used for public areas. To perform this, it is needed to measure the flow rate available within the system. What would you prefer to use in such a measurement? A) Pitot- static Tube B) Thermal (Hot-Wire and Hot-Film) Anemometers C) PIV D) Pitot Tube

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.4: Precision Measurement

Problem 21RQ: A(n) ________ displays a magnified image of a part on a screen for conducting measurement.

See similar textbooks

Similar questions

Qn) A)What is thermocouple? Explain measurement system using Thermocouple with a neat schematic sketch. Draw the characteristics and write its different types with properties.
Q: Venting system important for sanitary drainage systems, discuss the need of it and describe it’s main components and how it can be integrated with the plumbing drainage system.
Well Completion : Tubing leaks is one of well completion problems. the causes and method(s) to remediate the problem.
The bulk modulus of fluid (K) equals: Select one: O a. PV/AV O b. VAV/AP O c. None of all O d. PAV/V
1) An engineer wants to increase a pipeline diameter but maintain the volumetric flow rate. The entrance pressure must ________. increase decrease stay the same not enough information 2) Water is pumped down a pipeline. The feed to the pipeline is switched to honey, which has a higher viscosity. The pressure at the entrance of the pipeline will need to ________________ to maintain the same volumetric flow rate. increase decrease stay the same Please Explain Your "Original" Answers! NO COPY AND PASTE SOLUTIONS FROM CHEGG, STUDY.COM, etc.. Thanks for your help!
Duct installations are most economical with maximum use of: O 1) Fittings O 2) Straight duct runs O 3) Dampers to direct the air O 4) Larger fans
The following air streams mix in a building’s HVAC system upstream of the HVAC heating unit: 1,600 CFM outdoor air at 35°F and 70% RH mixes with 3,500 CFM of return air at 70°F and 40% RH. Assume the HVAC runs for 1 minute, so CFM is the same as cubic feet. a) What are the temperature and RH of the combined air stream? b) How much energy (units of BTU) does the HVAC heating unit need to add to the combined air stream to condition it to 80°F and 60% RH? c) If the conditioned air stream from the heating unit then mixes with 28,000 CFM of air at 70°F and 40% RH provided to the building from another source, what are the combined temperature and RH of the air in the building?
This type of compressor is commonly used in air conditioning systems in large buildings. b) screw a) centrifugal c) hermetic How to install the bulb of the thermostatic valve to the suction pipe. b) vertical c) diagonal a) horizontal
21. The following are the results of tests conducted on a centrifugal pump. Negative pressure head in suction pipe close to pump =22 cms of mercur y Pressure he id in delivery pipe close to pump=1'50 kg/cm2 Difference of level between the two gauges 0 50 metres SHP of the electric motor Discharge of the pump * Dianeter of the suction pipe Diameter of the delivery pipe Calculate the overall efficieney of the pump. -32 hp -010 cumeo %3D =20 cma 18 cms (78 17%)
A) What volume of oil to the cylinder is required to cause the cylinder to advance at a speed of 392 inches per minute if the piston diameter is 1.5 inches. a. 0.3 gpm b. 3 gpm c. 30 gpm d. 300 gpm B) How fast will that same cylinder retract if the flow rate is 3 gpm and the rod diameter is 1 inch. a. 7.06 inches per minute b. 70.6 inches per minute c. 706.0 inches per minute d. 7060 inches per minute
Identify the main sources of environmental pollution in the village/town/city
##What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing Adsorption Oxygen Generator (PSA) COMPs = Compressors POMPs = Pumps HEAT = Heat Exchanger PV = Flow Valves ST TANK = Storage Tank VENT = Vent DR = Drains PSV = Pressure Relief Valve In addition, what would be the possible problems that would require flexibility correction by adding expansion joints, spring supports, anchors and brackets?