40KN The beam, having the cross-section «I», is 60kNm subjected to a loading as shown in the figure. a) Check if the dimensions of the cross section of the beam are sufficient AB y! 1m 2m 1.5m 70mm 40mm 70mm according to the effect of the bending 60mm moment. b) Sketch the normal stress distribution on the cross section. 240mm 60mm Note that the allowable tensile and compressive normal stress is oa-10MPa. (cross-section of beam)

40KN The beam, having the cross-section «I», is 60kNm subjected to a loading as shown in the figure. a) Check if the dimensions of the cross section of the beam are sufficient AB y! 1m 2m 1.5m 70mm 40mm 70mm according to the effect of the bending 60mm moment. b) Sketch the normal stress distribution on the cross section. 240mm 60mm Note that the allowable tensile and compressive normal stress is oa-10MPa. (cross-section of beam)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
Determine the principal stresses acting at the 1 section using Mohr circle 150mm 5mm 5kN 60° 180mm 6mm 8mm 2 m 3 m 3 m 200mm
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
From the bracket connection shown. 1. Which of the following gives the stress due to axial load. a. 62.07 MPa b. 75.56 MPa c. 52.89 MPa d. 19.34 MPa 2. What is the value of ‘b’ that will make the maximum stress due to moment equal to that due to axial load? a. 150 mm b. 200 mm c. 250 mm d. 300 mm 3. What is the eccentricity? a. 300 mm b. 250 mm c. 150 mm d. 196.78 MPa
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
5KN 15KN DX Im лиш Х * Figure 6a Assume that the beam in Figure 6a has the cross-section shown in Figure 6b, and the maximum allowable tensile and compressive stress in the material used to manufacture the beam is 30 N/mm². Calculate the maximum Moment of Resistance for this beam. АУ 50 mm -한 +. 225 mm Figure 6b Assume that the beam in Figure 6a has the cross-section shown in Figure 6b. Determine whether this beam is adequate to support the load acting on it, as shown in Figure 6a (e.g. whether the beam has sufficient strength to resist the maximum Bending Moment calculated at Q24). Assume that the beam in Figure 6a has the cross-section shown in Figure 6c. Determine whether the beam is adequate to support the load acting on it, as shown in Figure 6a (e.g. whether the beam has sufficient strength to resist the maximum Bending Moment calculated at Q24).
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following gives the maximum bearing stress among all the plates? A.1.50 P/bt B.1.50 P/nd2 0.75P- C.0.75 P/bt 1.5P D.0.750 P/id2 0.75P- For the deformed plate shown in figure X, the magnitude of the shear strain at point D is nearest to 2 mm 5 mm A.0.229 rad B.0.004 rad C.0.573 rad D.0.010 rad 500 mm 500 mm Plates A and B are to be connected using bolts and two cover plates C and D as shown. The force exerted on plate A is 30 kN and the diameter of the bolts used is 25 mm. The thickness of all the plates is 15 mm. Which of the following is the shear stress experienced by either bolt? A.30.6 MPa F B.61.1 MPa B C.45.8 MPa D.15.3 MPa B
Determine the cracking moments for the section shown if f. ̟ = 27MPA. C 600mm 675mm 4-25mm Ø RSB 1. 75mm 400mm
= 5.29 Knowing that P Q = 480 N, determine (a) the distance a for which the absolute value of the bending moment in the beam is as small as possible, (b) the corresponding maximum normal stress due to bending. (See hint of Prob. 5.27.) THEMOM DV P nedw to absol be500 mm 500 mm pripoly not Alase BOLERON 9T AO mersib anamorp sode bol ng appiled: the batuda Fig. P5.29 edi te ating out A Daniloobo CV. D (5.6b) Q f 12 mm s mas i nadw bozudiruaib ebimnice di Tibe sade 2b2 B (10. busd bus bris to pages. eda sdtlanbi are noe minnas li batalize yo led ditw i most u tamom gaiboedshus en betrovalmisoled loads Dignst Box brol 18 mm
20MPA a In Figure , according to the stress condition of a stack of I-section beam. (30Mpa is the shear stress value.) 30MPA I- 40MPа 1-)Calculate the principal stresses, location and angle. A 2-)Calculate the stress components that will affect the plane in a section a-a that makes a 300 angle shown in the figure.