47 PHYSE 40.0 cm 20.0 cm 80.0 cm Figure shows uniform solid cylinder 80.0 cm long and 40.0 cm in diameter, with a small spherical portion removed from it. The diameter of this removed portion is 20.0 cm and its center is 20.0 cm from one end of the cylinder. Find the center of gravity of the remaining portion if the center of the sphere lies on the axis of the cylinder. Formula: Vsphere = (pid^3)/6; Vcylinder = (pid^2h)/4; (Vcyl - Vsphere) xcg = (Vcyl xcyl – Vsphere xsphere)

47 PHYSE 40.0 cm 20.0 cm 80.0 cm Figure shows uniform solid cylinder 80.0 cm long and 40.0 cm in diameter, with a small spherical portion removed from it. The diameter of this removed portion is 20.0 cm and its center is 20.0 cm from one end of the cylinder. Find the center of gravity of the remaining portion if the center of the sphere lies on the axis of the cylinder. Formula: Vsphere = (pid^3)/6; Vcylinder = (pid^2h)/4; (Vcyl - Vsphere) xcg = (Vcyl xcyl – Vsphere xsphere)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Similar questions

Find the elevation h (km) where the weight of an object is one-tenth its weight on the surface of the earth.
Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y of the plane region shown.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Locate the center of gravity of the composite body in the figure. All dimensions are expressed in cm. 2 3 m 2. 2.
Find the centroid’s x and y coordinates to 3 significant digits relative to the bottom right corner. Each semicircle has a radius of 4 cm. The dimensions in cm are not to scale.
A cube A is 30cm along each edge and weighs 1450N. It is attached to the square prism B which 15cm x 15cm x 2.4 meters and weighs 4700N/m3 . What height of B (in meters) will project above the surface if the specific gravity of the liquid is 1.50?
Set up and evaluate the integral that gives the volume of the solid formed by revolving the region about thexaxis. Step 1 From the figure consider the representative rectangle. The radius of the solid of revolution obtained by revolving the rectangle about the xacis is R(X) -y9- To find the volume of a solid of revolution with the-Select mathod, use the horizontal axis of revolution. Select disk shel Volume-VE
Find the dimension and surface area of the shape object according to the pappus-guldinus theorem
Scanned information in the form, find it according to the reference.Information on the UPN400 profile; its center of gravity belongs to ex = 2.65cm and its area to A = 91.5cm2 find the center of gravity of the given shape(THİS İS A QUESTİON) (Information about the upn 400 profile is given in the image.)
The meterstick shown is 100 cm long. It is free to pivot around its center of gravity (CG), which is at the 50 cm mark. There is a 25.0 N block hanging from the 80 cm mark. Decide where each of the other blocks should be placed, one at a time, to balance out the 25.0 N block. At what mark on the meter stick would you place a 18.0 N block to balance the 25.0 N block?
Find the centroid of the shown shaded area += 22 Cm K-21 Cm 35 cm
In the figure, a homogenous, planar plate with a constant thickness is given on the (x, y) axis set. Calculate the center of gravity M(xM, yM)of the plate by creating a table. (cm) only HANDWRITTEN answer needed ( NOT TYPED)