5-50. The check valve is used to regulate pressure in the pipe. If the stiffness of the spring is k = 80 kN/m and its uncompressed length is 120 mm, determine the maximum pressure in the tank if the lever is to remain in the horizontal position as shown. The plug at A is circular. Problem 5-50 300 mm- 150 mm

5-50. The check valve is used to regulate pressure in the pipe. If the stiffness of the spring is k = 80 kN/m and its uncompressed length is 120 mm, determine the maximum pressure in the tank if the lever is to remain in the horizontal position as shown. The plug at A is circular. Problem 5-50 300 mm- 150 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.75P: The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft...

See similar textbooks

Similar questions

asap
The operation of the exhaust and intake valves in an automobile engine consists of cam C, pushrod DE, rocker arm EFG which is hinged at F and on a spring , and valve V. If the compression on the spring is 20 mm when the valve is open, as indicated in the figure, determine the normal force acting on the lobe of the cam at C. Assume that the cam and the bearings at H, I, and J are smooth. The spring has a stiffness of 300N/m. draw the free body diagram
5-12. The following data were taken from an oxygen-bomb calorimeter test: weight of fuel pan and coal, 6.9359 g; weight of fuel pan, 6.0502 g; weight of water, 1600 g; water equivalent of apparatus, 490 g; temperature rise, 2.837 C; radiation temperature correction, 0.009 C (additive); thermometer calibration correction +0.003 c. Calculate the higher heating value of the coal in celories per gram and in Btu per pound.
8-22. The cylinder is confined by the brake, where 4, = 0.4. Determine the required compression in the spring in order to resist a torque of 800 N m on the cylinder. The spring has a stiffness of k = 3 MN/m and an unstretched length of 60 mm. End C of member ABC slides freely along the smooth vertical guide. Problem 8-22 250 mm 400 mm 200 mm
5-11. Determine the reactions at the supports. Problem 5-11 5 -3 m 400 N/m -3 m B
8-23. The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm. Both the plug and the sleeve are 50 mm long. Determine the axial pressure p that must be applied to the top of the plug to cause it to contact the sides of the sleeve. Alsa, how far must the plug be compressed downward in order to do this? The plug is made from a material for which E-5 MPa, v -0.45.
Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 84 N and (a) e = 30°, B = 25° and (b) e = 16°, B = 27° %3D F BI B L--n Answers: (a) Fn= N, F = N (b) Fn= N, F = the tolerance is +/-2%
Determine the spring constant k4 (N/m) if the extension of the whole system is 1.44 m when a force of 29.86 N is applied. Use k1 - 12.67 N/m, k2 - 11.1 N/m, k3 - 28.39 N/m, and k5 - 33.91 N/m. (Use 2 decimal places for the final answer.) k k3
FA BO К mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force on the spring FD and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17 ) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees ww
5-86. Operation of exhaust and intake valves in an automobile engine consists of the cam C, push rod DE, rocker arm EFG which is pinned at F, and a spring and valve, V. If the compression in the spring is 20 mm when the valve is open as shown, determine the normal force acting on the cam lobe at C. Assume the cam and bearings at H, I, and J are smooth. The spring has a stiffness of 300 N/m. 25 mm 40 mm E Prob. 5-86
In figure shown, the unstretched length of spring AC is 3 m. If the block is held in the equilibrium position, determine the mass of the block at D. 3 m- 4m- KAc=20 N/m 3m KAB=40 N/m KAD=30 N/m
The shafts shown have modulus of rigidity G1 and G2, derivethe differential equation of the system and determine the system naturalfrequency.