please use nscp 2015 5.) A reinforced concrete beam has a width of 300mm and an effective depth of 410mm. fc=27.1 MPa, fy =414.7 MPa.a. Compute the actual tensile stress in the reinforcing bars if he beam is reinforced for tensionwith a steel area of 3690 sq. mmb. compute the actual strain in the tension bars based from your answer in (a),b. Compute the actual compressive force acting on the section.c. Compute the factored moment capacity of the beam.d. compute the depth of compression block for a balance condition and the.e. balanced steel area.

Dear student, As per bartleby guidelines we are supposed to answer any three subdivisions(part d, b…

Answered: 5.) A reinforced concrete beam has a…

Engineering

Civil Engineering

5.) A reinforced concrete beam has a width of 300mm and an effective depth of 410mm. fc- 27.1 MPa, fy=414.7 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
The concrete post in the figure is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm?. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Bearing | 1000 kN plate Steel Concrete 300 mm 300 mm Section a-a The stress in concrete = MPa (use up to 4 significant figures). The stress in steel = MPa (use up to 4 significant figures).
A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A = 40,000 mm2 and length L = 2 m (see figure). Before the load P is applied, the middle post is shorter than the others by an amount s = 1.0 mm. The allowable compressive stress in the concrete is 20 MPa and E of concrete is 30 GPa. What is the minimum load P (kN) needed to close the gap? P S
SITUATION 21 A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction, and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in x direction, 320 kN compression in the y direction, and 180 kN tension in the z direction. For Steel, Poisson's Ratios = 0.30 and E=200 GPa. 4. Determine the total strain in x direction due to the triaxial loading 5. What single uniformly distributed load in the x direction that would produce the same deformation in the x direction as he orig nal loading.
A beam, which is rectangular, has a base of 250 mm, and d = 575 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given b) Determine the value of "As"
!! Show Complete & Detailed Solution w/ FBD !!The bronze bar 3 m long with a cross-sectional area of 350 mm^2 is placed between two rigid walls. At a temperature of –25C, there is a gap  = 2.5 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use α = 18.0 x 10–6 /C and E = 80 GPa.
A RECTANGULAR ALUMINUM BLOCK IS 110mm LONG IN THE X DIRECTION, 70mm WIDE IN THE Y DIRECTION AND 85mm THICK IN THE Z DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF 210 KN (COMPRESSION), 170 KN (TENSION) AND 230 KN (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON'S RATIO = 1/4 & E= 72 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETERMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME Z DEFORMATION AS THE ORIGINAL.
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It is reinforced with 4-36 mm diameter bars at the tension side of the beam placed 75 mm above the bottom of the beam. f = 25 MPa, fy = 414 MPa, E, = 200,000 MPa. Which of the following is the nominal moment capacity of the beam.
A rectangular reinforced concrete beam with width of 250 mm and effective depth of 500 mm is subjected to 150 kN-m bending moment. The beam is reinforced with 4-25 mm o bars. Use alternate design method and modular ratio n = 9. 1. What is the maximum stress of concrete? 2. What is the maximum stress of steel? 3. What is the total compressive force in concrete? b = 250 009=P -0000- b = 250 d-x nA. 4-25 mm Ø ΝΑ
A beam, which is rectangular, has a base of 250 mm, and d = 625 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given a) Determine the value of "a". %3D
For the concrete beam shown, the modulus of elasticity is 25 Gpa for the concrete and 200 GPa for the steel. Knowing that b= 200 mm and d-450 mm, and using an allowable stress of 12.5 MPa for the concrete and 140 MPa for the steel, calculate (a) the required area As of the steel reinforcement if the beam is to be balanced, (b) the largest allowable bending moment. Hint: The design of a reinforced concrete beam is said to be balanced if the maximum stresses in the steel and concrete are equal, respectively, to the allowable stresses os and oc. BU 176 13 A 40 l: 40 9,0 244 في المداد ko J
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.