5. A symmetric I-section of size 180 mm x 40 mm, 8 mm thick is strengthened with 240 mm x 10 mm rectangular plate on top flange as shown is Fig. below. If permissible stress in the material is 150 N/mm?, determine how much concentrated load the beam of this section can carry at centre of 4 m Given ends of beam are simply supported. span. 240 mm

5. A symmetric I-section of size 180 mm x 40 mm, 8 mm thick is strengthened with 240 mm x 10 mm rectangular plate on top flange as shown is Fig. below. If permissible stress in the material is 150 N/mm?, determine how much concentrated load the beam of this section can carry at centre of 4 m Given ends of beam are simply supported. span. 240 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.10P: During construction of a highway bridge, the main girders are cantilevered outward from one pier...

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
For the cantilever beam arrangement shown below, address the following: (a) Determine the forces acting on the plane (y-z) containing point B. (b) Determine the stress state at point B. 400 lb 500 lb 1.5 in. 2 in 1.5 in. 10 in. B 1 in.
A symmetric I-section of size 180 mm × 40 mm, 8 mm thick is strengthened with 240 mm × 10 mm rectangular plate on top flange as shown is Fig. below. If permissible stress in the material is 150 N/mm^2, determine how much concentrated load the beam of this section can carry at centre of 4 m span. Given ends of beam are simply supported.
Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following:a. Calculate the tension of the cable.b. Determine the diameter of the wire if the allowable stress is 125 MPa.c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm fat- 40 mm- 30 pm 30 mm 10 mm 10 mm
The figure below shows a simply supported prismatic beam with an applied uniform load. The labeled points A through E are equally spaced (at the quarter points) along the length of the beam and are located at the top of the beam section. Points A and E may be assumed to be located directly above the supports. Rank the points, from greatest to least, on the basis of the absolute value of normal stress in the beam section.
4. A wood post 12 in. by 12 in. is braced by four steel angles. The wood post and the pieces of angles are exactly the same length of 20 feet. The reinforced post carries a total compressive load of 200 kips. For steel: E = 29 x 10^3 ksi, for wood: Area = 0.938 sq. in., E = 1.9 x 10^3 ksi a. Find the axial stress (in kips) in the steel. b. Find the axial stress in the wood. c. Find the deformation (in inches) if the length of the reinforced post is 12 ft. IVERSI
The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section.
2 kip/ft 6 in 10 in B. 40 kip 16 in D. 16 In 5 ft 5 ft 10 ft The simply-supported beam-column above is subjected to a uniformly distributed load and an axial load, as shown. Assume that the Internal resultants on the cross-section passing through point D are as follows: • ND -40 kip • VD 0 Mp = +100 kip-ft Which of the following is closest to the longitudinal normal stress at point D? O-78.1 psi +235 psi O-153 psi O-1.77 ksi H:
The lever must exert a force of P = 3800 Ibs at B as shown. The lever lengths are a = 11 in. and b = 47 in. The allowable bending stress for the lever is 12600 psi. If the lever height h is to be 3.5 times the lever thickness t (i.e., h/t = 3.5), what is the minimum thickness t that can be used for the lever? h Cross section Lever a Answer: t = i in.
Read the question carefully and give me right solution according to the question.. Please answer all. Don't miss anything. Figure 5 shows a rigid horizontal beam ABCE which is supported by a pair of rectangular bars CD at C. The cross-sectional size of each of the rectangular bar is 37.5 × 12.5 mm. Modulus of elasticity of the bar is E=80 GPa. Vertical loads of 17.5 kN and 35 kN act at points B and E, respectively.Compute:i) Vertical displacement of point Bii) Vertical displacement of point EIf it is given that the allowable displacement of point C is 1 mm, determine the minimum thickness of rectangular bar CD required. The width of the rectangular bar should be kept unchanged at 37.5 mm.