5. Two vertical cylindrical storage tanks are full of liquid water, density atmoshere. One is 10 m tall, 2 m diameter, the other is 2.5 m tall with diameter 4 m. What is the total force (in Newton) from the bottom of each tank to the water and what is the pressure ( in kpa)at the bottom of each tank? Note: Substitute your corresponding assigned number to the blank kg/m3, the top open to the

5. Two vertical cylindrical storage tanks are full of liquid water, density atmoshere. One is 10 m tall, 2 m diameter, the other is 2.5 m tall with diameter 4 m. What is the total force (in Newton) from the bottom of each tank to the water and what is the pressure ( in kpa)at the bottom of each tank? Note: Substitute your corresponding assigned number to the blank kg/m3, the top open to the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 12 kN sphere is attached to a 4 kN sphere by a cable. Both spheres have the same diameter of 1.2 m and the weight and volume of the cable is negligible. If the spheres are thrown in water, calculate the following:a. The draft of the 4 kN sphere in meter.b. The tension in the cable in kilonewton.c. The exposed volume of the 4 kN sphere in cubic meter.d. Percentage of submerged volume of 2 spheres.
2. A 3,000 gallon tanker is carrying industrial alcohol (donaity-48 23 D. /h) finteBurton to the Selene Building. Find the weight (N) of the industrial alcohol if the tanker is67% full. (Round to nearest whole number)
An oil of SG 0.9 is contained in a vessel. At a point the height of oil is 40 m . Find the corresponding height of water at that point.
A concrete block is attached to the gate as shown. If the water level is 1.3 m from the bottom of the container, there is no reaction force at A.What would be the reaction force for the level shown?Note 1: Specific gravity of concrete is 2.4.Please show clear workings with explanations to steps taken. I don't just want the answer, I want to understand the process to answering this question. Thanks
Question 3 A triangular water trough is "a" metres wide and "a" metres deep, as shown in Figure 3. If the trough is filled with water, calculate the magnitude and location of the resultant force acting on the triangular end plates (shaded in grey). The density of water is 1000 kg/m³ (ignore the atmospheric pressure). Use the value of "a" corresponding to the last digit of your SID from Table 1. "a" m "am Figure 3: Triangular water trough a=7
The tank depicted in in the diagram is located at an oil refinery. There is rectangular hatch locatedon one side that gives access for maintenance. The company will be replacing the hatch door andhas hired you to assist with the design requirements.a) Describe to the client what is the resultant force and center of pressure on the wall labelled ‘A’ onthe diagram above. (P1)b) Calculate the resultant force acting on the hatch door and the location of the centre of pressure.(P2)II. (M1) The client is procuring a new hydraulic lifting jack. The jack is rated to lift 2000kg. Given thatthe diameter of the pumping piston is 25 mm and the lifting piston is 40 mm, calculate for theclient:a) The force needed on the pumping piston to raise the max load.b) The pressure in the oil.c) If the pumping piston moves 1cm with every pump, what distance does the lifting piston move
1. Two pipes A & B caries an oil of specific gravities 0.9 & 1.2 respectively. The center of the pipe A is 75 cm above the pipe B. The height of oil in right limb is 35 cm. Also, the mercury level difference is found in right limb as 60 cm. Find the pressure difference between these two pipes in kPa. Also find the pressure equivalent in water head in mm. A. The difference of pressure between two pipes (PA-Pa) (Unit is in kPa) = B. Equivalent to Water head in mm =
Problem Solving: Input your final answer on the space provide. Note: Use three decimal places and no need to input the unit. A tank for medical use has a cylindrical shape, determine its mass (in kgs) if the density of the fluid is 2.3 kg/m^3 if the tank has a diameter of 300mm and 2m length.
a drum has gasoline s.g=0.9, with oil s.g=0.8 and sea water s.g=1.03. the depth of the liquid is 0.8m, 0.5m, and 1.0 for gasoline, oil and sea water.1. find absolute pressure at depth 1.2m 2.find the depth at 1.8m 3. find the force F at depth 2.1m when diameter of drum is 0.5m
4. Assuming standard condition, what is the altitude in ft where the density is 0.001845 slug/ft3?
1. A building is 512 m high. What must be the minimum water pressure (psi) in a pipe at ground level to get water up to a restaurant on the top floor. Neglect friction loss in pipe. 2. The pressure of a gas supports 2.75 ft of Mercury. Calculate the height of water column (in meters) which the gas pressure will support. 3.A water tank of cross-sectional area 2.5 m2 and height 120 in contains 1500 (US) gallons of water. If the density of water is 1000 kg/m3, calculate the force on the base of the tank.
Find the pressure represented by a column of a. 10cm of water.b. 5cm of oil of relative density 0.75.c. 2cm of mercury