5.10 The boost regulator in Figure 5.18a has an input voltage V, 6V. The average out- put voltage V, 12V and average load current I, 0.5 A. The switching frequency is 20 kHz. If L = 250 µ.H and C = 440 µ.F, determine (a) the duty cyclek (b) the ripple current of inductor Al, (c) the peak current of inductor I2, (d) the ripple voltage of filter capacitor AVe, and (e) the critical values of L and C. 4 Dm M1 VD Ve Load Vo Va (a) Circuit diagram

5.10 The boost regulator in Figure 5.18a has an input voltage V, 6V. The average out- put voltage V, 12V and average load current I, 0.5 A. The switching frequency is 20 kHz. If L = 250 µ.H and C = 440 µ.F, determine (a) the duty cyclek (b) the ripple current of inductor Al, (c) the peak current of inductor I2, (d) the ripple voltage of filter capacitor AVe, and (e) the critical values of L and C. 4 Dm M1 VD Ve Load Vo Va (a) Circuit diagram

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 20-V-rms 60-Hz ac source is in series with an ideal diode and a 100-Ω resistance. Determine the peak current and PIV for the diode.
In a given circuit below is connected to an AC signal with 240V peak in a 4:1 transformer. Sketch the voltagewave form at VA and Vo as practical diode. (Show Complete Solution)
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
A load consists of XL=70 and XC=150 are connected in parallel across 120 Volt supply.The reactive power of the circuit is.......
The average (DC) value of a half-wave rectified voltage with a peak value of 200 V is: a. 63.7 V b. 127.3 V c. d. OV 141 V 2. Voltage regulation is determined by: a. load current b. Zener current and load current c. changes in load resistance and output voltage d. changes in no-load voltage and full-load voltage When a 60-Hz sinusoidal voltage is applied to the input of a full-wave rectifier, the output frequency is: a. 120 Hz b. 60 Hz c. 240 Hz d. 0 Hz
A step down de chopper is connected to an R5 2 and L-10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, lo and the peak to peak ripple current as an absolute value and as percentage of de value.
Determine the peak to peak ripple voltage and the ripple factor for a bridge rectifire using capacitor input filter. The load resistance is 2 kn while the d.c voltage across the loadis 12 V. Assume supply frequency to be 50 Hz and ideal diodes. The capacitor of 100 µFis used in the filter circute.
Derive the average and rms values of output voltages and currents for three phase semi converter. Power Electronics
A buck regulator has Vsource 15 V. The average output voltage required is Vo=6 V with peak-to-peak ripple input of 10 mV, the switching frequency is 20 kHz and the peak-to-peak ripple of current of the inductor L is 0.6 A. Calculate the duty cycle and the values of Land Crequired.
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).