50 100 100 50 h i O None of the above 75 * g 75 a b d 75 For rupture of the net section, what factor would have to be true for the section to rupture at line efg instead of abcd? O The diameter of hole f is more than twice as large as either the diameter of hole b or hole c O The section will fail at line abcd no matter what because it is closest to the end of the member O Line efg won't rupture because net sections yield in tension instead of rupture

50 100 100 50 h i O None of the above 75 * g 75 a b d 75 For rupture of the net section, what factor would have to be true for the section to rupture at line efg instead of abcd? O The diameter of hole f is more than twice as large as either the diameter of hole b or hole c O The section will fail at line abcd no matter what because it is closest to the end of the member O Line efg won't rupture because net sections yield in tension instead of rupture

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.) A thin plate PQR is deformed so that the corner Q is displaced downward 1.0 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges. 5) A pin mado of steo1 ie insorted in o short hanging TAOodon mombor ond iG 1used to Supnort lond E - 20
Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following gives the maximum bearing stress among all the plates? A.1.50 P/bt B.1.50 P/nd2 0.75P- C.0.75 P/bt 1.5P D.0.750 P/id2 0.75P- For the deformed plate shown in figure X, the magnitude of the shear strain at point D is nearest to 2 mm 5 mm A.0.229 rad B.0.004 rad C.0.573 rad D.0.010 rad 500 mm 500 mm Plates A and B are to be connected using bolts and two cover plates C and D as shown. The force exerted on plate A is 30 kN and the diameter of the bolts used is 25 mm. The thickness of all the plates is 15 mm. Which of the following is the shear stress experienced by either bolt? A.30.6 MPa F B.61.1 MPa B C.45.8 MPa D.15.3 MPa B
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a diameter of 4 mm., if the failure strength of the rivets in shear is 370 N/mm2 and the ultimate tensile strength of the plate is 465 N/mm?, determine the necessary rivet pitch b (mm) if the joint is to be designed so that failure due to shear in the rivets and failure due to tension in the plate occur simultaneously. Calculate also the joint efficiency n (%). 3 mm 4 mm diameter
"messenger_media?thread_id%=D100002917920802&attachment_id%3891210971774069&message_id%3Dmid.%24CAAAA Question 3 For the truss shown, determine the forces in members (a) BD; and (b) BF. 4 m4 m4 m-4 m- A B C 6 m E F G H O00 20 kN 20 kN 20 kN A BD-40kN (C); BF-33.33kN (T)
IjẩẩREẩjP3.4 Nylon rod (1): d Steel tube (2) FIGURE P3.7
is a structure ttiade of sletidet tretribers which aré joined together at their énd point select one H. Support O B.Pilar 0d.Beam OE Shot by Hisense H12
Two 10inch-15.3 lb channels are welded together as shown in the figure. Compute for the values of Centroids, and lxx for the figure. 1. Determine ybar? 2. Determine lxx (Centroidal)
Determine the principal stresses acting at the 1 section using Mohr circle 150mm 5mm 5kN 60° 180mm 6mm 8mm 2 m 3 m 3 m 200mm
Ro blem 2 20" го Given Base Rate A36 (Fye36 Ksi) WI2X5 20" B= N= 20 in t= 17/2" W 12 x 50 (de12.2", bf: 8.08 in) fc: 5 ksi A= A2 Determine the max Tu that Can be applied to this base Plate ? biet: ) determine u banaal on A, (2) Chorse the Smaller af tw valus
Please solve sub-part- ii completely and accurate with correct calculations. Thank you!