6- Set BX to 4567H, CX to FEDCH and SP to A59FH, then run the instructions: PUSH BX PUSH CX a. What is the new value of SP ? b. Display the memory locations where you pushed the values of BX and CX in the stack.
Q: Microprocessor Systems Question: A 20-bit address bus, an 8-bit processor uses a 3-to-8 decoder to…
A: The solution can be achieved as follows.
Q: What is the maximum memory size that can be connected to a processor with a lower order address bus…
A: In this question we will find maximum memory size that can be connected to a processor...
Q: 3. What are the high and low addresses of the memory ranges defined ! by each of the chip selects…
A: We will calculate memory range for given system .
Q: 1- What does the VOH parameter of a logic IC refer to? a) The highest permissible output…
A: As per our policy, i am attempting question first, The inverter's minimum output high voltage is…
Q: The number $5678 resides in data RAM $300 and $301 in little endian order. The number $1234 resides…
A: CODE IN AVR:
Q: Write a program to add the following five data bytes stored in memory locations starting from XX60H,…
A: The stored data is given as Memory LocationDataXX64H27HXX63H12HXX62H4FHXX61H32HXX60H1AH
Q: Q2/ A) Draw the logic circuit for each of the following: 1) The operations (1101 -1010) and (1101 +…
A:
Q: Digital logic design Make the truth table And And prove that it is equal to A+B+C
A: To prove: (A⊕B)⊕C=A⊕(B⊕C)=A⊕B⊕C Which is equals to A+B+C Use the truth table for EX-OR gate:
Q: Suppose that initially the contents of the registers are A:A7 B:69 SP:004E Y:B804and that memory…
A: Given data, Initially, the memory location 0048 – 004F are set to zero. Step-1 The most…
Q: Write program to load the content of memory location 0x0700 into register R3 then set D6,D7 and…
A: The problem can be solved in the following way:
Q: Prove the equality of the following Boolean expression (AB)’.(CD)’=(AB+CD)’. State this theorem.…
A: (AB)’.(CD)’=(AB+CD)’ R.H.S = (AB+CD)’ = AB' . CD' = (A'+B')(C'+D') L.H.S = AB'…
Q: Flag Register is a special purpose. Name two types of registers used in 8086 microprocessor.…
A: MOV AL, 50 → positive numberMOV BL,32→poistive number ADD AL,BL…
Q: Use any example which uses stack memory with appropriate instructions (PUSH,POP)
A:
Q: question1:In a memory system, data is 16-bit wide. Break the information into bytes with their…
A: solution:1)Big-Endian method:-In Big Endian machine, first byte of binary representation of he…
Q: For a Core2 descriptor that contains a base address of 00333000H, a limit of 0000166AH, and…
A: Given that core 2 descriptor base address is 00333000H. Thus starting Location of descriptor is…
Q: what are the application of Flip – Flop. b- What is the difference between the Flip – Flop circuit…
A: In this question we will write about applications of flip flops...
Q: rite a program to PUSH RO, R1, and R3 of Bank onto the stack and POP them back into RS, R6, and R7…
A: Stack work in LIFO manner (Last in first out ) . It means the data stored in last will be first to…
Q: Write a program that counts the number of zeroes in a 32-bit value. Store the result in register r1.
A: METHODOLOGY: ARM supports logical shift and rotates operation which can rotate the contents of a…
Q: How to store (1050000)10 in register $s0? Write down the instructions that stores the data in $s0…
A:
Q: VpD d) For the given circuit Fill the truth table and identify the type of logic gate Q3 For the…
A: In this question we are asked to fill the table. and then identify the gate. that FET's given are…
Q: Design an adder for excess-3 decimal digits using a ROM. Add two excess-3 digits and give the…
A: The excess-3 code is equivalent to converted as add to 3.
Q: Convert the following values to a 4-byte memory map assuming each is stored as an int :…
A: 1AEEF5AA16 is already in the hexadecimal number system. Answer: 1AEEF5AA16 = 1AEEF5AA H.
Q: Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and…
A:
Q: Q. 1 There are different types of memories used in 8086 microprocessor one of them is called Stack.…
A:
Q: d) For the given circun Fill the truth table and identify the type of logic gate For the transistor…
A: Given circuit is -
Q: Q: Suppose a data stored in register A =(A5) hex implement the following micro - operation: Set bits…
A:
Q: For all questions show all your works in details Q#1: A. Convert the binary number to decimal: 10111…
A: As per our policy I will solve only 3 parts: A) Binary to decimal Hence decimal value is 23 for…
Q: Q2: Consider a line of code- LDD $C100. Before execution of this line of code, the memory locations…
A: We need to select correct option for given statement
Q: If R0 = 0x20008000, after run STMDB r0!, {r3, r9, r7, r1, r2} command what is the r7 register memory…
A: According to the question, we need to find the memory start address for the resister r7.
Q: (a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits,…
A:
Q: Q3=100011 solve Q3 O Q3=010110 Q3=110011 Q3/Assume that the microprocessor can directly address 64K…
A: We need 4 memory of 8k * 8 for 16k * 16 , We need to find out address for 4 memory .
Q: Short-answer Question) Given a BCD decade counter with only the Q outputs available, show what…
A: for the given BCD decade counter with only the Q outputs, given that, (a) 0001 (b) 0011 (c) 0101…
Q: In a 4-bit ripple up-counter how many clock pulses will you apply, starting from state 0 0 0 0, so…
A:
Q: Draw a combinational logic circuit of a four input multiplexor where the inputs (X3;X2;X1;X0) are…
A: MULTIPLEXER: The multiplexer is a combinational circuit that is used to connect multiple input…
Q: 1) The control flags type and operation? 2) Compare between CS & CX registers? 3) Assume SS=5000H,…
A: Flag registor of 8086 microprocessorControl flags - the control flags enable or disable certain…
Q: An AVR has 0XFFF as the address of its last byte in the RAM and it has the same value OXFFF as the…
A: The memories have the same number of locations since the address bus has 12 bits. We can store each…
Q: What is the maximum memory size that can be connected to a processor with a lower order address bus…
A: What is the maximum memory size lower order address bus 24 lines higher order address bus of 4…
Q: For the ROM memory chip shown, find the capacity (including units): . organization: is this memory…
A: The ROM is a Non Volatile Memory.
Q: D- A в H Figure 1 3. Referring to the logic circuit in Figure 1, determine: a. The simplified…
A:
Q: Q1) Write an assembly program to duplicate each memory location block (size N) starting at address…
A:
Q: Group A Question 1: 1. What is the function of cash memory? 2. Give me two differences between data…
A: As per our policy I have to do Question 1 first three parts only. 1. The primary function of cache…
Q: 1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40…
A:
Q: What are the values of the inputs a, b, c, d, e, f and g for a Seven-Segment LED that displays the…
A:
Q: G"JIAssume that the microprocessor can directly address 64K with a and 8 data pins The memory map…
A: We need to find out range for memory .
Q: Question 5.K-Map is used for A. Logic Minimization B. Expression Maximization C. Summing of Party…
A: K - Map - It is a method which is used to minimize boolean expressions using graphical techniques.…
Q: There are different types of memories used in 8086 microprocessor one of them is called Stack. You…
A: As per our policy i have attempted first three sub-part only. (i) In stack memory the allocation…
Q: system with 16 bits address bus can access 2^16 memory space. Estimate the size of each memory IC…
A: In this question we will find size of memory....
Step by step
Solved in 2 steps with 1 images
- Write program to load the content of memory location 0x0700 into register R3 then set D6,D7 and complement D4,D5 for date in R3 then store the result in memory location 0x0800 .The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?
- ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LGConsider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
- Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address Ox1000. The original data are stored in the memory starting from address 0x800. it is an electrical engineering question . this is the full information about the question!- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it1- Write a program in assembly language to perform the following logic ci CL DL [5100]– 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX, FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX,
- Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuitWhat is the hexadecimal value stored in Register A after the following assembler has executed? LDA #0x71 NOTA NOTA LDR B,#0x71 ADC A,B LDR B,#0xEB ADC A,B NOTA LDR B,#0xD5 ADC A,B LDR B,#0x53 SBC A,B LDR B,#0x19 SBC A,B LDR B,#0x5E SBC A,BWrite a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5, R6, and R7 of Bank 3. Also, mention the value of SP register after every PUSH and POP operation. this question is asked in microprocessor and microcontroller